IronCraft FMH Series страница 11 Скачать руководство пользователя

Страница: 11 / 48

FLAIL MOWER – FMH Series

DANGER

Do not operate the implement while wearing loose fitting clothing that can give rise to entanglement in

parts of the machine.

DANGER

Do not operate the implement when tired, not in good condition or under the influence of alcohol or drugs.

CAUTION

If the use of the machine is required at night or in conditions of reduced visibility, use the lighting system

of the tractor and possibly an auxiliary lighting system.

3.2.

EQUIPMENT SAFETY INSTRUCTION

WARNING

Use the flail mower for its intended purpose only. Improper use can damage the flail mower and cause

serious injury to persons, animals, or death.

DANGER

The machine should be used by a single operator driving the tractor.

WARNING

Any unauthorized modification of the machine may cause problems in safety and relieves the Manufacturer

from any liability for damages or injuries that may result to operators, third parties and objects.

WARNING

Before using the machine, familiarize yourself with its controls and its working capacity.

WARNING

Do not leave the flail mower unattended with tractor engine running.

WARNING

Do not operate flail mower on too muddy, sandy or rocky soils.

WARNING

Keep the machine clean from debris and foreign objects which may damage functioning or cause injury.

WARNING

Do not use the machine if the category of the connecting pins of the flail mower does not match that of

the trac- tor hitch system.

WARNING

Do not use the machine with missing bolts, screws, pins or safety pins, safety guards etc.

Содержание FMH Series

















































Результаты поиска

Содержание FMH Series

Отзывы:

Похожие инструкции для FMH Series

Бренды по названию

Популярные бренды

IronCraft FMH Series, Руководство по эксплуатации

Результаты поиска

Содержание FMH Series

Отзывы:

Похожие инструкции для FMH Series

Бренды по названию

Популярные бренды