IronCraft FMH Series страница 2 Скачать руководство пользователя

Страница: 2 / 48

FLAIL MOWER – FMH Series

Congratulation for purchasing your new

IronCraft

flail mower!

This machine has been designed and manufactured following all safety and quality requirements needed

for a safe and satisfactory use over time.

A careful reading of this manual will permit you to familiarize with your new equipment, and will provide

you all the tools needed to use it safely.

A proper maintenance and knowledge of the safety rules of use will allow to obtain the best performance

and a long service life of the machine.

The Safety Alert Symbol used throughout this manual and on safety decals of the

machine indicates the presence of potential hazard to the operator. When you see

this symbol, be alert and carefully read the message that follows it.

The Safety Alert Symbol is used in conjunction with following Signal Words, according to the

degree of possible injuries that may result operating the implement:

DANGER

Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury, and

includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe

practices.

CAUTION

Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury. It

may also be used to alert against unsafe practices.

IMPORTANT

Indicates instructions or procedures that, if not observed, can cause damage to equipment or environment.

NOTE

Indicates helpful information.

READ, UNDERSTAND, and FOLLOW the safety messages following the Safety Alert Symbol and Signal

Words. Failure to comply with safety messages could result in serious bodily injury or death.

Содержание FMH Series

















































Результаты поиска

Содержание FMH Series

Отзывы:

Похожие инструкции для FMH Series

Бренды по названию

Популярные бренды

IronCraft FMH Series, Руководство по эксплуатации

Результаты поиска

Содержание FMH Series

Отзывы:

Похожие инструкции для FMH Series

Бренды по названию

Популярные бренды