IronCraft FMH Series Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 48

IronCraft FMH Series Скачать руководство пользователя страница 30

FLAIL MOWER - FMH Series

If the deflection is about 10 mm, the tension is correct.

If is not so, proceed with the adjustment in the following way (see picture below):

• loosen the four nuts (1) under the gearbox which lock it to the frame;

• loosen the two bolts (2) fixing the extension tube to the side plate of the frame;

• while holding the screw (3), loosen the lock nuts (4);

• tighten the tension nut (5) if the tensioning found is too low (deflection of belts higher than 10 mm);

unscrew the tension nut (5) if the tensioning found is too high (deflection of belts lower than 10 mm).

• retighten the lock nuts (4) and the two bolts (2) fixing the extension tube to the side plate of the frame;

• move the gearbox in order to restore the position of the extension tube perpendicular to the side plate

of the flail mower;

• retighten the four nuts (1) under the gearbox;

• reposition the safety cover in his original place.

1

2

4

3

5

«
...
28
29
30
31
32
...
»

Содержание FMH Series

















































Отзывы:

Нет отзывов