Intex PureSpa SB-HW10 Скачать руководство пользователя страница 17

Страница: 17 / 27

346

S AVE THESE INSTRUCTIONS

(346PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 08/10/2019

English

Page 17

LED CODE CHART

LED Reading

CAUSE

SOLUTION

E81

Transmission signal failure

• Reset the RCD, restart all over again.
• Place the control panel within 5 m (16 ft) of the

control base unit.

• Press and hold POWER button for 5 seconds to

turn off and charge the panel again.

• If problem persists, contact Intex Service Center.

E90

No water

• Turn off and unplug the control unit.
• Ensure the outlet cover grid is clean and free from

obstructions.

• Clean or replace the cartridge, see Maintenance

and Storage section.

• Ensure the in/outlet connections on the spa tub and

lter pump are not blocked.

• Keep the spa water properly sanitized to ensure a

clean and unclogged

lter cartridge.

• If problem persists, contact Intex Service Center.

E94

Water temperature too low

• If the ambient temperature is below 39°F (4°C), we

recommend not to use the spa.

• Turn off and unplug the control unit, add some

warm water to raise the spa water temperature
above 41°F (5°C), then press the

button to heat

up the water to the desired temperature.

• If problem persists, contact Intex Service center.

E95

Water temperature too high

• Turn off and unplug the control unit. When the water

has cooled down, plug the RCD and restart all over
again.

• Turn the heater off, then press the

lter and bubble

buttons to lower the water temperature.

• If problem persists, contact Intex Service Center.

E96

System Error

• Turn off and unplug the control unit. Plug the RCD

and restart all over again.

• If problem persists, contact Intex Service Center.

E97

Dry-

re Protection

• Contact Intex Service Center.

E99

Water temperature sensor broken • Contact Intex Service Center.

END

After 72 hours of continuous

heating operation, the pump will

hibernate automatically. The rapid

heating function is disabled.

• Press the

button to re-active the

lter pump.

BLANK

Control panel battery has no power

or in “Power Saving Mode” waiting

to be placed on the control base

recessed channel.

• Press any button to reactivate the control panel.
• Reset the RCD, restart all over again and charge

the control panel again.

• Make sure the surface between the back of the

control panel and the control base recessed channel
is clean, dry and free of obstruction.

• If problem persists, contact Intex Service Center.

Содержание PureSpa SB-HW10




























Результаты поиска

Содержание PureSpa SB-HW10

Отзывы:

Похожие инструкции для PureSpa SB-HW10

Бренды по названию

Популярные бренды

Intex PureSpa SB-HW10, Руководство пользователя

Результаты поиска

Содержание PureSpa SB-HW10

Отзывы:

Похожие инструкции для PureSpa SB-HW10

Бренды по названию

Популярные бренды