Intex PureSpa SB-HW10 Скачать руководство пользователя страница 6

Страница: 6 / 27

346

S AVE THESE INSTRUCTIONS

(346PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 08/10/2019

English

Page 6

When ordering parts, be sure to quote the model number and part numbers.

PARTS (continued)

Before assembling your product, please take a few minutes to check the contents

and become familiar with all the parts.

REF.

NO.

DESCRIPTION

QTY.

PART NO.

4 ADULTS 6 ADULTS

CONTROL BASE

12833

SIDE COVER HINGE BASE

12771D

SIDE COVER HINGE FIXER

12772D

CONTROL BASE SIDE COVER

12770D

CONTROL PANEL

12839

CONTROL PANEL BOLT WRENCH

11053

SPA/COVER INFLATION HOSE

11830

SPA CONTROL INLET/OUTLET O-RING

11699

SPA CONTROL AIR INLET O-RING

11687

SPA DRAIN PLUG

11995

SPA DRAIN VALVE ADAPTOR

11713

FILTER CARTRIDGE HOUSING

11798

FILTER CARTRIDGE

11692

FILTER CARTRIDGE HOUSING LID

11797

INLET/OUTLET PLUG

11739

SPA TUB

10067

12841

SPA COVER

11841W

12107W

SPA COVER INFLATABLE BLADDER (PRE-INSTALLED IN SPA COVER)

11689

12108

GROUND CLOTH

11717

12109

CHEMICAL DISPENSER

12735

TEST STRIPS

11855

WRENCH

11742

AIR PRESSURE RELEASE VALVE CORE

12589D

HOSE ADAPTOR

12773

MALE BUCKLE

11994

FEMALE BUCKLE

11993

DEFLATION OUTLET CAP

12775D

DEFLATION HOSE ADAPTOR

12774

SPA FILTER MOTOR

12777

SUCTION FITTING

11695

SPA SUCTION FITTING

Self-contained spa

ttings. – For multiple outlet use only. – Wall mounting only.

Replace suction

ttings within 3 installed year. – Tool required: screwdriver.

Spa suction

tting maximum

ow rate: 8.5 gpm (510 gph)

• Check suction strainer

tting and fasteners for damage or tampering before each use of the spa.

• For service and winterization instructions refer to “Maintenance” and “Storage” sections.

• Read and follow all instructions, save these instructions for future reference.

Содержание PureSpa SB-HW10




























Результаты поиска

Содержание PureSpa SB-HW10

Отзывы:

Похожие инструкции для PureSpa SB-HW10

Бренды по названию

Популярные бренды

Intex PureSpa SB-HW10, Руководство пользователя

Результаты поиска

Содержание PureSpa SB-HW10

Отзывы:

Похожие инструкции для PureSpa SB-HW10

Бренды по названию

Популярные бренды