Interroll SH 1110 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 64

background image

Interroll Roller Conveyor SH 1110

Installation

Version 1.0 (06/2022) en
Translation of original operating instructions

23

The universal support (7) is installed at the top on the profile of the side frame (1).

Requirement:

R

The module is shut down.

4

Loosen screw (6) in the universal support, but do not remove it.

4

Bring clamping plate (5) with universal support (7) from below into position at the profile of
the side frame.
The profile of the side frame is located between clamping plate and universal support.

4

Tighten the screw (6) at the desired location.

4

Push side guide bracket (2) onto the mounting bracket (4) of the universal support (7).

Fasten screws with a tightening torque of 6 Nm.

4

Position side guide bracket and firmly tighten screw (3) in the side guide bracket.

«
...
21
22
23
24
25
...
»

Содержание SH 1110

































































Отзывы:

Нет отзывов

Похожие инструкции для SH 1110

Бренд: NEC Страницы: 5

Бренд: Samsung Страницы: 2

Бренд: Unisen Страницы: 9

Бренд: Zavoli Страницы: 26

Бренд: Aries Страницы: 3

Бренд: Neuspeed Страницы: 2

NexSys iON 24-L1-20-4.7

Бренд: EnerSys Страницы: 12

FusionDome FDW75CF2

Бренд: Moog Страницы: 13

Бренд: DAVIS Страницы: 32

Zerolite Wheelset

Бренд: Vuelta Страницы: 12

Бренд: BASETech Страницы: 8

Бренд: Stack Страницы: 2

Бренд: Beurer Страницы: 24

Бренд: Berlebach Страницы: 2

Бренд: Moza Страницы: 57

Бренд: Nauticam Страницы: 33

Бренд: Crivit Страницы: 70

37-Key Audio/MIDI Interface and Controller Ozonic

Бренд: M-Audio Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды