Interroll SH 1110 Скачать руководство пользователя страница 56

Страница: 56 / 64

Interroll Roller Conveyor SH 1110

Version 1.0 (06/2022) en

Translation of original operating instructions

Decommissioning and disposal

When disposing the motor oil, observe the disposal documents of the motor manufacturer.

The packaging must be recycled to provide environmental relief.

Environmental protection regulations

For all work on and with the module, the legal regulations concerning waste avoidance and
proper disposal and recycling must be followed.

NOTICE

Substances with a water hazard class, such as greases and oils, hydraulic oils,
coolants or cleaning agents with solvents may not be allowed to come into contact
with the ground or reach the sewer system!

Store, transport, catch and dispose these substances in suitable containers!

Observe the notices on the supply containers.

Observe any additional national regulations.

Содержание SH 1110

































































Результаты поиска

Содержание SH 1110

Отзывы:

Похожие инструкции для SH 1110

Бренды по названию

Популярные бренды

Interroll SH 1110, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SH 1110

Отзывы:

Похожие инструкции для SH 1110

Бренды по названию

Популярные бренды