manualshive.com logo in svg

Interlogix UltraView IP PTZ 36X, Руководство пользователя

Поделиться
Скачать
Interlogix UltraView IP PTZ 36X Скачать руководство пользователя страница 62

Chapter 7: Alarm setup 

58 

UltraView IP PTZ 36X Camera User Manual 

3.  Select an input type in the

 

Relay status

 box. 

This refers to the sensor type. You can select Normal Open (NO) or Normal 
Close (NC) according to the sensor type. 

Note: 

In order for a camera to record an alarm, the recording option and type 

must be enabled on the Schedule screen. See “Defining a recording 
schedule” on page 27 

4.  Specify the response method for both the alarm and PTZ links. 

Alarm linkage: 

Select how you want to be notified of an external alarm. 

Select the Alarm Linkage tab and check one or more of the response 
methods: 

 

E-mail link

 

Check to send an e-mail when an alarm is detected. 

 

Trigger recording 

Check the input option shown to select the video channel 
from which to start recording.

 

Trigger alarm output

 

Check which of the camera’s alarm outputs is triggered:  
Alarm Output 1 or Alarm Output 2. More than one output 
can be selected.

 

 

PTZ linkage

: Select how you want the camera’s PTZ to respond to an 

external alarm. Select the PTZ Linkage tab and check one or more of the 
response methods: 

 

Preset

 

Check to enable this response and enter the preset number 
to be used. 

 

Patrol (Preset tour) 

Check to enable this response and enter the preset tour 
number to be used.  

Pattern( Shadow tout)

 

Check to enable this response and enter the shadow tour 
number to be used. 

 

 

See “Controlling a PTZ camera” on page 72 for more information on using 
PTZ dome cameras with this camera. 

5.  If required, copy the settings of this alarm input to other alarm inputs. Under 

“Copy Alarm Input To” check the inputs to which to copy these settings. 

6.  Click 

Save

 to save changes. 

To set up an alarm relay output: 

1.  In the 

Alarm Parameters

 folder, click the 

Alarm Output

 subfolder to open its 

screen. 

2.  Select an alarm output. 

3.  Select the alarm output delay time. 

The alarm output delay is the length of time that an alarm output triggers 
before stopping. Select a 

Delay

 option: 5, 10, and 30 seconds, 1, 2, 5, and 10 

Содержание UltraView IP PTZ 36X



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды