Intergraph InterServe 05 Setup Скачать руководство пользователя страница 61

Страница: 61 / 75

Other Hardware Errors

CD-ROM drive LED does not light

Reason

Solution

CD-ROM drive power cable is not attached.

Open the base unit and ensure power cable
is properly attached.

Floppy disk drive/combo drive LEDs do not light

Reason

Solution

Disk drive power cable is not attached.

Open the base unit and ensure power cable
is properly attached.

Floppy disk drive/combo drive not recognized

Reason

Solution

BIOS is not configured properly.

Configure the Floppy A and B parameters
under Standard to the required settings.

Disk drive power cable is not attached.

Open the base unit and ensure the power
cable is properly attached.

Floppy data cable is not attached properly.

Open the base unit and ensure the floppy
cable is properly attached at both ends.

Unsuccessful connection to serial device

Reason

Solution

Communication parameters between server
and serial device do not match.

Change the parameters so the server and
serial device match each other.

Содержание InterServe 05 Setup












































































Результаты поиска

Содержание InterServe 05 Setup

Отзывы:

Бренды по названию

Популярные бренды

Intergraph InterServe 05 Setup, Руководство по установке

Результаты поиска

Содержание InterServe 05 Setup

Отзывы:

Бренды по названию

Популярные бренды