Intellinet 523868 Скачать руководство пользователя

Страница: 20 / 56

2.2.6.4.1 IGMP

This screen is for

configuring the IP

multicast route

mode and IGMP

(Internet Group

Management

Protocol)

parameters.

IP Multicast Route

Mode:

Configure a

multicast route

protocol to run

or disable.

IGMP Version:

Select which

version to run.

default is “V2.”

IGMP Query Interval:

Set the number of seconds between two query packets. default is set at

125 seconds.

IGMP Query-Max-Response:

Set the response time when the host reports to its multicast group.

default is set at 10 seconds.

NOTE:

When setting IGMP, select the corresponding interface to configure parameters, then

click “Modify.” Changes will be updated in the display window. To save any changes and

make them effective immediately, click “Submit.” Click “Refresh” to refresh the settings.

2.2.6.4.2 DVMRP

This function is used for

configuring DVMRP

(distance Vector

Multicast Routing

Protocol).

Network DVMRP is:

enable or disable

DVMRP for a specific

network.

Select the corresponding

network address to configure parameters, then click “Modify.” Changes will be updated in the

display window. To save any changes and make them effective immediately, click “Submit.”

Click “Refresh” to refresh the settings.

NOTE:

Before setting this page, make sure that

IP Multicast Route Mode

on the IGMP screen

is set to “dVMRP.”

2.2.6.4.3 PIM-DM

This screen for configuring

PIM-dM (Protocol-

Independent Multicast –

dense Mode).

Status:

enable or disable

PIM-DM for a specific

interface.

Select the corresponding

interface to configure

parameters, then click

WEb MANAgEMENT

Содержание 523868

























































Результаты поиска

Содержание 523868

Отзывы:

Похожие инструкции для 523868

Бренды по названию

Популярные бренды

Intellinet 523868, Руководство пользователя

Результаты поиска

Содержание 523868

Отзывы:

Похожие инструкции для 523868

Бренды по названию

Популярные бренды