INTELLICYT iQue Screener PLUS Скачать руководство пользователя страница 19

Страница: 19 / 112

iQue

Screener PLUS Hardware Manual: Part Number 11811 Rev B, Safety

Operational Precautions

Ambient Temperature and Humidity

Operating temperature is between 15°C and 30°C (59°F and 86°F) and < 80% relative humidity.

Area of Use

•

The iQue Screener PLUS is designed to fit on a laboratory bench top.

•

Provide a safety perimeter of 15 cm (6 inches) around the instrument and computer to allow proper

ventilation and to protect the instrument and computer from accidental liquid spills.

•

Take special care while handling fluids around the instrument.

•

Do not allow uncontained fluids to enter the interior of the instrument or computer.

•

Immediately clean up spills.

•

Do not place anything on top of the flow cytometer, including sample tubes and racks.

•

Before manually cleaning the system, turn off the instrument and unplug the power cord.

Electrical Precautions

Electrical devices pose the risk of an electric shock. To reduce the risk of an electric shock, do not open

the back or side service panels while the system is plugged in. Allow only authorized personnel to remove

any other panels from this device.

Always use the provided power cords, power supplies, and cables. Do not abuse the cords. Never use the cords to

pull the plug from an outlet. Keep cords away from heat, oil, or sharp edges. Damaged cords increase the risk of

electric shock.

CAUTION:

The instrument must be plugged into an IntelliCyt approved uninterruptable power supply (UPS). The UPS

must be plugged into a standard, grounded, or earthed mains electrical outlet, conforming to local codes. Non-

grounded or non-earthed mains outlet adaptors must not be used.

Содержание iQue Screener PLUS

















































































































Результаты поиска

Содержание iQue Screener PLUS

Отзывы:

Бренды по названию

Популярные бренды

INTELLICYT iQue Screener PLUS, Руководство по оборудованию

Результаты поиска

Содержание iQue Screener PLUS

Отзывы:

Бренды по названию

Популярные бренды