manualshive.com logo in svg

INTELLICYT iQue Screener PLUS, Руководство по оборудованию

Поделиться
Скачать
INTELLICYT iQue Screener PLUS Скачать руководство пользователя страница 15

11

iQue

®

 Screener PLUS Hardware Manual: Part Number 11811 Rev B, Safety

General Precautions

WARNING

Use this product only in the manner described in this guide. When 

used other than as specified, the safety protections may be impaired. 

Failure to adhere to safety precautions and/or procedures outlined in 

this document may result in system failure or personal injury. IntelliCyt 

Corporation shall not be held liable under any circumstances. 

WARNING

BIOHAZARD! 
•  Use proper laboratory practices when handling any hazardous 

materials.

•  Make sure that biohazards do not contaminate iQue Screener 

PLUS components.

•  In the event that system contamination occurs, contact customer 

support for applicable cleanup procedures.

DANGER

If smoke, abnormal noise, or strange odor is present, immediately 

shutdown the system and notify Customer support. It is dangerous to 

continue using the system. 

WARNING

For safe operation of the iQue Screener PLUS, the system must be 

connected to an IntelliCyt approved uninterruptable power supply.

General Warnings

THE iQue SCREENER PLUS IS INTENDED FOR GENERAL LABORATORY AND RESEARCH USE ONLY. IT IS NOT 

INTENDED FOR IN VITRO DIAGNOSTIC TESTING. READ THE ENTIRE iQue PLUS SCREENER SYSTEM HARDWARE 

MANUAL BEFORE ATTEMPTING TO OPERATE THE INSTRUMENT. DO NOT ATTEMPT TO PERFORM ANY PROCEDURE 

BEFORE CAREFULLY READING ALL INSTRUCTIONS. ALWAYS FOLLOW PRODUCT LABELING AND MANUFACTURER’S 

RECOMMENDATIONS. IF THERE IS ANY QUESTION AS TO HOW TO PROCEED, CONTACT INTELLICYT.
IF THIS INSTRUMENT IS USED IN A MANNER NOT SPECIFIED BY THE MANUFACTURER, THE PROTECTION PROVIDED 

BY THE INSTRUMENT MAY BE IMPAIRED.
COMPLY WITH ALL NATIONAL HEALTH AND SAFETY STANDARDS SUCH AS THE USE OF BARRIER PROTECTION. THIS 

MAY INCLUDE, BUT IS NOT LIMITED TO, PROTECTIVE EYEWEAR, GLOVES, AND SUITABLE LABORATORY ATTIRE WHEN 

OPERATING OR MAINTAINING THIS INSTRUMENT.
The information in this user guide is subject to change at any time without notice. Products may change in response 

to technological advancements.

Safety

Содержание iQue Screener PLUS

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды