Intel Xeon 5500 Series Скачать руководство пользователя страница 18

Страница: 18 / 98

LGA1366 Socket

Thermal/Mechanical Design Guide

2.4

Package Installation / Removal

As indicated in

Figure 2-6

, access is provided to facilitate manual installation and

removal of the package.

To assist in package orientation and alignment with the socket:

• The package Pin1 triangle and the socket Pin1 chamfer provide visual reference for

proper orientation.

• The package substrate has orientation notches along two opposing edges of the

package, offset from the centerline. The socket has two corresponding orientation
posts to physically prevent mis-orientation of the package. These orientation
features also provide initial rough alignment of package to socket.

• The socket has alignment walls at the four corners to provide final alignment of the

package.

See

Appendix F

for information regarding a tool designed to provide mechanical

assistance during processor installation and removal.

2.4.1

Socket Standoffs and Package Seating Plane

Standoffs on the bottom of the socket base establish the minimum socket height after
solder reflow and are specified in

Appendix C

Similarly, a seating plane on the topside of the socket establishes the minimum
package height. See

Section 4.2

for the calculated IHS height above the motherboard.

Figure 2-6. Package Installation / Removal Features

alignment

walls

orientation

notch

orientation

post

access

Pin1 triangle

Pin1 chamfer

alignment

walls

orientation

notch

orientation

post

access

Pin1 triangle

Pin1 chamfer

Содержание Xeon 5500 Series



































































































Результаты поиска

Содержание Xeon 5500 Series

Отзывы:

Похожие инструкции для Xeon 5500 Series

Бренды по названию

Популярные бренды

Intel Xeon 5500 Series, Руководство по конструкции

Результаты поиска

Содержание Xeon 5500 Series

Отзывы:

Похожие инструкции для Xeon 5500 Series

Бренды по названию

Популярные бренды