Intel Xeon 5500 Series Скачать руководство пользователя

Страница: 43 / 98

Thermal/Mechanical Design Guide

Quality and Reliability Requirements

Quality and Reliability

Requirements

6.1

Test Conditions

The Test Conditions provided in

Table 6-1

address processor heatsink failure

mechanisms only. Test Conditions, Qualification and Visual Criteria vary by customer;

Table 6-1

applies to Intel requirements.

Socket Test Conditions are provided in the LGA1366 Socket Validation Reports available
from socket suppliers listed in

Appendix A

Table 6-1.

Heatsink Test Conditions and Qualification Criteria (Sheet 1 of 2)

Assessment

Test Condition

Qualification Criteria

Min

Sample

Size

1) Humidity

Non-operating, 500 hours, +85°C and 85%

R.H.

No visual defects.
As verified in wind tunnel:

• Mean

+ 3s + offset not to exceed

value in

Table 5-1

• Pressure drop not to exceed value in

Table 5-1

2) Board-Level

UnPackaged Shock

50G+/-10%; 170+/-10% in/sec; 3 drops

per face, 6 faces.

No damage to heatsink base or pipe.
No visual defects.
As verified in wind tunnel:

• Mean

+ 2.54s + offset not to

exceed value in

Table 5-1

• Pressure drop not to exceed value in

Table 5-1

3) Board-Level

UnPackaged Vibration

5 Hz @ 0.01 g2/Hz to 20 Hz @ 0.02 g2/Hz

(slope up).
20 Hz to 500 Hz @ 0.02 g2/Hz (flat).
Input acceleration is 3.13 g RMS.
10 minutes/axis for all 3 axes on all

samples.
Random control limit tolerance is ±3 dB.

No damage to heatsink base or pipe.
No visual defects.
As verified in wind tunnel:

• Mean

+ 2.54s + offset not to

exceed value in

Table 5-1

• Pressure drop not to exceed value in

Table 5-1

4) First Article

Inspection

Not Applicable

Meet all dimensions on 5 samples.
Meet all CTF dimensions on 32 additional

samples with 1.33 Cpk (mean + 4s).
If samples are soft-tooled, a hard tool plan

must be defined.

5) Shipping Media:

Packaged Shock

Drop height determined by weight and may

vary by customer; Intel requirement in

General Supplier Packaging Spec.
10 drops (6 sides, 3 edges, 1 corner)

No visual defects

1 box

6) Shipping Media:

Packaged Vibration

0.015 g2/Hz @ 10-40 Hz, sloping to

0.0015 g2/Hz @ 500 Hz, 1.03 gRMS,

1 hour/axis for 3 axes

No visual defects

1 box

7) Gravitational

Evaluation

Required for heatpipe designs.
3 orientations (0°, +90°, -90°)

As verified in wind tunnel, mean

+ 3s

+ offset not to exceed value in

Table 5-1

Содержание Xeon 5500 Series



































































































Результаты поиска

Содержание Xeon 5500 Series

Отзывы:

Похожие инструкции для Xeon 5500 Series

Бренды по названию

Популярные бренды

Intel Xeon 5500 Series, Руководство по конструкции

Результаты поиска

Содержание Xeon 5500 Series

Отзывы:

Похожие инструкции для Xeon 5500 Series

Бренды по названию

Популярные бренды