Intel SR2612UR - Server System - 0 MB RAM Скачать руководство пользователя страница 71

Страница: 71 / 162

Intel

Server System SR2612UR Service Guide

10. Connect the cable to the installed PCI RAID board as shown below

Figure 57. Connect the cable to PCI RAID Card

11. Reinstall the top cover and tighten the captive screw.

12. Reinstall the power cords.

Installing and Removing the Server Board

Removing the Server Board

To remove the server board, follow these steps:

1. Power down the enclosure and remove the power cord(s).

2. Remove the top cover from the enclosure by loosening the captive screw with a

Phillips screwdriver on the right-rear of the enclosure.

3. Slide the top cover back and lift it from the enclosure.

4. Remove the processor air duct.

5. Remove the PCI riser assembly.

6. Remove the Intel

RMM3, if installed.

7. Disconnect power cables, P1, P2, P3 and Front Panel logic cable, from

Motherboard as shown below.

Содержание SR2612UR - Server System - 0 MB RAM



































































































































































Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды

Intel SR2612UR - Server System - 0 MB RAM, Руководство по обслуживанию

Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды