Intel SR2612UR - Server System - 0 MB RAM Скачать руководство пользователя страница 41

Страница: 41 / 162

Intel

Server System SR2612UR Service Guide

Hot-Swap SAS/SATA Backplane

The backplane serves as an interface between the midplane board and the system drives.

The hot-swap backplane provides support for both SAS and SATA hard drives. There are
no hard drive cables that connect to the backplane. All hard drive control signals are
routed from the midplane board, which plugs directly into the backplane.

Figure 18. 3.5-inch Hot-Swap SAS/SATA Backplane Components (Front View)

Figure 19. 3.5-inch Hot-Swap SAS/SATA Backplane Components (Rear View)

SAS/SATA Hard Disk Drive Connectors

Backplane Power Connector

Midplane Board Connector

Server Board/Midplane GPIO Connector

Содержание SR2612UR - Server System - 0 MB RAM



































































































































































Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды

Intel SR2612UR - Server System - 0 MB RAM, Руководство по обслуживанию

Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды