Intel SR2612UR - Server System - 0 MB RAM Скачать руководство пользователя страница 65

Страница: 65 / 162

Intel

Server System SR2612UR Service Guide

14. Reinstall the power cord(s).

Power Supply Replacement

Complete the following steps to remove and install a power supply in the Intel

Server

System SR2612UR.

1. Ensure the AC power cord(s) are disconnected from the enclosure.

2. Remove the top cover from the enclosure by loosening the captive screw on the

right-rear of the enclosure with a Phillips screwdriver.

3. Slide the top cover back and lift it from the enclosure.

4. Remove the power supply by pushing in and holding the green latch in the

directions shown in the following figure.

Figure 45. Removing the Power Supply

5. Using the handle, carefully slide the power supply out of the enclosure chassis.

6. Reinstall a new power supply by inserting it into the chassis enclosure until it clicks

into place.

7. Reinstall the top cover and tighten the captive screw.

8. Reinstall the power cord(s).

Replacing the Backplane Board

The following sections describe how to replace the backplane board.

Содержание SR2612UR - Server System - 0 MB RAM



































































































































































Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды

Intel SR2612UR - Server System - 0 MB RAM, Руководство по обслуживанию

Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды