Intel SR2612UR - Server System - 0 MB RAM Скачать руководство пользователя страница 17

Страница: 17 / 162

Intel

Server System SR2612UR Service Guide

System Rear View

Figure 2. Intel

Server System SR2612UR Rear View

Note: The SAS expansion port is either part of the PCI RAID adapter card or is a separate

multi-port PCI SAS card. Currently, the qualified and supported PCI RAID card are
Intel

RAID Controller SRCSASJV, Intel

RAID Controller SRCSASLS4I and Intel

RAID Controller SASWT4I. Please refer to the Intel Customer Support web site under the
link for these RAID controllers at:

http://www.intel.com/support/motherboards/server/

About the Disk Drives and Drive Carriers

The Intel

Server System SR2612UR supports up to 12 SAS and/or SATA disk drives.

SAS and SATA disk drives are not supported within the same appliance enclosure;
however, only in specific configurations (as shown later in this chapter).

Each disk drive is mounted on a drive carrier assembly (shown in the following figure)
with a push-button lever for quick installation and removal.

Содержание SR2612UR - Server System - 0 MB RAM



































































































































































Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды

Intel SR2612UR - Server System - 0 MB RAM, Руководство по обслуживанию

Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды