Intel SR2612UR - Server System - 0 MB RAM Скачать руководство пользователя страница 22

Страница: 22 / 162

Intel

Server System SR2612UR Service Guide

Latest drivers, firmware
updates (BIOS, BMC, and
FRUSDR), and utilities

Available for download at:

http://www.intel.com/support/motherboards/server/sr2612ur/

Click the “Software and Drivers” link on the left side of the web
page.

To make sure your system
falls within the allowed
power budget

Power Budget Analysis Tool

Available at:

http://www.intel.com/support/motherboards/server/sr2612ur/

For software to manage
your Intel

server

Intel

System Management Software

Available at:

http://www.intel.com/go/servermanagement/

Table 1. Server System References

For this information or

software

Use this Document or Software

Содержание SR2612UR - Server System - 0 MB RAM



































































































































































Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды

Intel SR2612UR - Server System - 0 MB RAM, Руководство по обслуживанию

Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды