Intel SR2600UR - Server System - 0 MB RAM Скачать руководство пользователя страница 106

Страница: 106 / 234

Server System SR2600UR/SR2625UR Service Guide

Figure 75. Installing Tape Drive Assembly into the Server System

4. Connect the 4-pin tape power cable to the tape drive.
5. Connect the other end of the power cable to the power connector on the back side of

the backplane.

6. Connect one end of the data cable to the tape drive.
7. Connect the other end of the data cable to the SATA connector on the server board

or the SAS/SATA connector on the SAS/SATA add-in PCI card.

Installing a Sixth Hard Disk Drive (Intel

Server System

SR2600UR only)

To install a sixth hard disk drive into Intel

Server System SR2600UR/SR2625UR, your

system must meet the following requirements:

•

You must purchase the sixth SAS/SATA Hard Disk Drive (HDD) kit, order number

ASR2500SIXDRV.

•

You must purchase an additional 3.5 inch hard disk rive.

After purchasing the sixth SAS/SATA Hard Disk Drive (HDD)kit and the 3.5 hard disk

drive, use the following instructions to install the hard drive.

AF0000

Содержание SR2600UR - Server System - 0 MB RAM











































































































































































































































Результаты поиска

Содержание SR2600UR - Server System - 0 MB RAM

Отзывы:

Бренды по названию

Популярные бренды

Intel SR2600UR - Server System - 0 MB RAM, Руководство по обслуживанию

Результаты поиска

Содержание SR2600UR - Server System - 0 MB RAM

Отзывы:

Бренды по названию

Популярные бренды