manualshive.com logo in svg

Intel S875WP1-E, Спецификация, Страница: 67 / 117

Поделиться
Скачать
Intel S875WP1-E Скачать руководство пользователя страница 67

S875WP1-E TPS 

BIOS Features 

Revision 4.0

 

 

 

55

 

6.6  Recovering BIOS Data 

Some types of failure can destroy the BIOS. For example, the data can be lost if a power outage 
occurs while the BIOS is being updated in flash memory. The BIOS can be recovered from a 
diskette using the BIOS recovery mode. When recovering the BIOS, be aware of the following: 

•

  Because of the small amount of code available in the non-erasable boot block area, 

there is no video support. The user can only monitor this procedure by listening to the 
speaker or looking at the diskette drive LED. 

•

  The recovery process may take several minutes; larger BIOS flash memory devices 

require more time. 

•

  Two beeps and the end of activity in the diskette drive indicate successful BIOS 

recovery. 

•

 

A series of continuous beeps indicates a failed BIOS recovery. 

To create a BIOS recovery diskette, a bootable diskette must be created and the BIOS update 
files copied to it. BIOS upgrades and the Intel Flash Memory Update Utility are available from 
Intel Customer Support through the Intel World Wide Web site. 

 

NOTE 

Even if the computer is configured to boot from an LS-120 diskette (in the Setup program’s 
Removable Devices submenu), the BIOS recovery diskette must be a standard 1.44 MB 
diskette not a 120 MB diskette. 

For information about  

Refer to 

The BIOS recovery mode jumper settings 

Section 5.14 

The Boot Device Priority menu in the BIOS Setup program 

Section 7.1.6.1 

 

6.7 Boot 

Options 

In the BIOS Setup program, the user can choose to boot from a diskette drive, hard drives,  
CD-ROM, or the network. The default setting is for the diskette drive to be the first boot device, 
the hard drive second, the ATAPI CD-ROM third, and the network fourth. The fifth device is 
disabled.  

6.7.1 

CD-ROM and Network Boot 

Booting from CD-ROM is supported in compliance to the El Torito bootable CD-ROM format 
specification. Under the Boot menu in the BIOS Setup program, ATAPI CD-ROM is listed as a 
boot device. Boot devices are defined in priority order. Accordingly, if there is not a bootable CD 
in the CD-ROM drive, the system will attempt to boot from the next defined drive. 

The network can be selected as a boot device. This selection allows booting from the on-board 
NIC or a network add-in card with a remote boot ROM installed. 

Содержание S875WP1-E






















































































































Отзывы:

Нет отзывов