manualshive.com logo in svg

Intel Omni-Path Director Class Switch Series, Руководство по установке

Поделиться
Скачать
Intel Omni-Path Director Class Switch Series Скачать руководство пользователя страница 88

You can check the progress of the update with the CLI command

showLastBcFwRetCode -all

. The system returns information similar to the

following:

Edge-> showLastBcFwRetCode -all

Module Board Controller Firmware Last Exit Code: 3: In Progress 

Edge-> showLastBcFwRetCode -all

Module Board Controller Firmware Last Exit Code: 0: Success

Proceed to Step 3.

3. Reboot the switch.
4. Verify the version of the BCFW and BIOS by running the CLI commands

bcfwversion

 and 

biosversion

. The system should return information similar

to the following:

Board Controller Firmware Version: CGBCP429 

System BIOS Version: QA3ER962

Updating Director Class Switches

Update the BCFW and BIOS on Director Class switches (DCS) using the instructions in 

Performing the Upgrade

 on page 88.

NOTE

The instructions upgrade both the Master and Slave MM.

Performing the Upgrade

1. At the master MM prompt, enter the following command to update the master and

slave: 

sftp> put QA3ER962.q7.spkg A:/firmware/bios.pkg

The system returns information similar to the following:

Uploading QA3ER962.q7.spkg to /firmware/A:/firmware/bios.pkg 

QA3ER962.q7.spkg

100% 8193KB   12.4MB/s      00:00

You can check the progress of the update with the CLI command

showLastBiosRetCode -all

. The system returns information similar to the

following:

MasterM201-> showLastBiosRetCode -all

M201 System BIOS Last Exit Code: 3: In Progress 

M202 System BIOS Last Exit Code: 0: Success 

MasterM201-> showLastBiosRetCode -all

M201 System BIOS Last Exit Code: 0: Success 

M202 System BIOS Last Exit Code: 0: Success

NOTE

DO NOT REBOOT AT THIS TIME. Wait until both the BCFW (via 

bcfwupdate

) and

the BIOS (via 

biosupdate

; see Step 2) have been updated, then reboot.

Proceed to Step 2.

A.5  

A.5.1  

Intel

®

 Omni-Path Fabric—Q7 BIOS Update

Intel

®

 Omni-Path Fabric Switches Hardware

Installation Guide

June 2019

88

Doc. No.: H76456, Rev.: 10.0

Содержание Omni-Path Director Class Switch Series




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды