Intel Omni-Path Director Class Switch Series Скачать руководство пользователя страница 42

Страница: 42 / 91

1. Loosen the 4 thumbscrews from the switch cover. There are 3 screws on the top,

and 5 screws on the back. Lift the cover on a 45-degree angle, then pull to

remove.

Figure 19.

Switch Cover Thumbscrews (Top View)

2. Holding the fan assembly on the sides lift straight up and rotate the fan assembly

180 degrees as shown in the following figure.

Figure 20.

Fan Assembly Rotation

3. Lower the fan assembly straight down. The airflow direction indicators should now

face towards the rear of the chassis as shown in the following figure.

NOTE

Make certain to provide strain relief for the wire assembly.

Intel

Omni-Path Fabric—Installation

Intel

Omni-Path Fabric Switches Hardware

Installation Guide

June 2019

Doc. No.: H76456, Rev.: 10.0

Содержание Omni-Path Director Class Switch Series




























































































Результаты поиска

Содержание Omni-Path Director Class Switch Series

Отзывы:

Бренды по названию

Популярные бренды

Intel Omni-Path Director Class Switch Series, Руководство по установке

Результаты поиска

Содержание Omni-Path Director Class Switch Series

Отзывы:

Бренды по названию

Популярные бренды