Intel Omni-Path Director Class Switch Series Скачать руководство пользователя страница 64

Страница: 64 / 91

Figure 47.

Module Installation 4

5. Chassis management slot leaf only: If the leaf module is in one of the chassis

management slots (i.e., L101 or L102) the mechanical release latch (MRL) must

be moved in order to install the leaf. To move the MRL, loosen the thumbscrew

attached to the Serial, Ethernet, Chassis EEPROM Board (SEEB) module, then pull

down to release the MRL as shown in the following figure. This allows enough

clearance for leaf module to be installed.

Figure 48.

Module Installation 5

Intel

Omni-Path Fabric—Installation

Intel

Omni-Path Fabric Switches Hardware

Installation Guide

June 2019

Doc. No.: H76456, Rev.: 10.0

Содержание Omni-Path Director Class Switch Series




























































































Результаты поиска

Содержание Omni-Path Director Class Switch Series

Отзывы:

Бренды по названию

Популярные бренды

Intel Omni-Path Director Class Switch Series, Руководство по установке

Результаты поиска

Содержание Omni-Path Director Class Switch Series

Отзывы:

Бренды по названию

Популярные бренды