10 | Integral Audio | Installation Instructions
Continued on next page...
41. I
nStall
t
Hreaded
I
nSertS
(
part
2)
Using a utility knife, carefully trim the PVC jacket out
of the center of the Self-Sealing Threaded Inserts as
shown. Insert the 1” Hex Bolt through the Installation
Tool. Then thread the 1” Hex Bolt into the Threaded
Insert. Be sure the “nubs” on the Installation Tool
face the top of the Threaded Insert. These “nubs” are
what grip the Insert and prevent it from turning during
installation.
47. I
nStall
tHe
e
ncloSure
Place the enclosure back into the boot. Connect
the Banana Plugs to the Terminal Cup. Insert the
Rosette Thumbscrews through the Mounting Brackets
and screw into the Threaded Inserts. If you made a
mistake drilling the holes and the Thumbscrews do
not line up, drill larger holes in the mounting brackets.
NOTE: We recommend coating the threads of the
Rosette Thumbscrews with grease to keep them
operating smoothly and avoid corrosion.
48. H
ow
to
r
eMoVe
tHe
f
alSe
f
loor
The False Floor Panel slides through the hatch
opening and rests on the floor supports. To remove,
simply push down on the edge near the rear seat
backs, lift, and remove – clean, simple, easy!
46. M
ount
tHe
f
loor
S
upportS
(
part
2)
Mount the Stand-offs centered approx 2” in from
the edges of the enclosure. Mark and drill 1/8” pilot
holes. Attach the supports with the Screws and Cup
Washers.
IMPORTANT: Tighten the screws until the metal
Washer is recessed below the top of the Rubber
Stand-off, providing a soft surface for the False Floor.
If this is not done, the floor will rattle on the washer/
screw-head.
45. M
ount
tHe
f
loor
S
upportS
(
part
1)
The floor supports are assembled with one Rubber
Stand-off, one Cup Washer, and one #10 x 1.5” Pan
Head Screw.
NOTE: The Stand-offs may have warped in transit.
To get them to stack cleanly, wrap a few turns of
electrical tape around them at the seam. Remove
after installation.
44. M
ount
tHe
S
peaKer
Mount the speaker with the #10 x 1” Black Pan Head
Screws. The speaker is snug fit! Tighten the screws
in a “star” pattern, go slowly and take care not to strip
them. Make sure the speaker flange is flush against
the enclosure – the gasket on the back of the speaker
flange MUST make an airtight seal.
43. w
IrIng
& t
erMInal
c
up
Split and strip the ends of the remaining 2 feet of
16AWG Speaker Cable. Crimp the (4) female ¼”
Quick Disconnects to the wire and connect one
pair the Terminal Cup and the other to the speaker,
observing correct polarity. If possible, we strongly
encourage soldering these connections instead of the
(4) disconnects. Mount the Terminal Cup using the
(4) #6 x ¾” Black Pan Head Screws.
42. I
nStall
t
Hreaded
I
nSertS
(
part
3)
Insert the Threaded Inserts into the holes drilled
in the previous step. Keep the Insert vertical and
keep the head of the Insert flush against the sheet
metal and carefully tighten the bolt by hand with a
wrench (do not use a powered tool of any kind) until
you begin to feel resistance and the insert is secure.
Take your time - do not over-tighten. Remove the 1”
Hex bolt. If you have trouble with an Insert, you can
remove it by partially unthreading the 1” Hex bolt and
tapping it with a hammer.
F. PREP & INSTALL THE ENCLOSURE