Integra DTR-50.4, Инструкция по эксплуатации, Страница: 70 / 112

Advanced Operations
En-70
■
Hue
*1*4*6
`
–50 to 0 to +50
With this setting, you can adjust the color hue between
“
–50 ” and “ +50 ”.
■
Saturation
*1*4*6
`
–50 to 0 to +50
With this setting, you can adjust saturation. “ –50 ” is the
weakest color. “ +50 ” is the strongest color.
■
Color Temperature
*4*6
`
Warm
`
Normal
`
Cool
With this setting, you can adjust the color temperature.
■
Gamma
*4*6
`
–3 to 0 to +3
With this setting, you can adjust the incoming picture’s
R (red), G (green), and B (blue) color signal in relation to
the output color signal.
■
Red Brightness
*4*6
`
–50 to 0 to +50
With this setting you can adjust the brightness of red color.
“
–50 ” is the darkest. “ +50 ” is the brightest.
■
Red Contrast
*4*6
`
–50 to 0 to +50
With this setting you can adjust the contrast of red color.
“
–50 ” is the least. “ +50 ” is the greatest.
■
Green Brightness
*4*6
`
–50 to 0 to +50
With this setting you can adjust the brightness of green
color. “
–50 ” is the darkest. “ +50 ” is the brightest.
■
Green Contrast
*4*6
`
–50 to 0 to +50
With this setting you can adjust the contrast of green color.
“
–50 ” is the least. “ +50 ” is the greatest.
■
Blue Brightness
*4*6
`
–50 to 0 to +50
With this setting you can adjust the brightness of blue
color. “
–50 ” is the darkest. “ +50 ” is the brightest.
■
Blue Contrast
*4*6
`
–50 to 0 to +50
With this setting you can adjust the contrast of blue color.
“
–50 ” is the least. “ +50 ” is the greatest.
Note
• “ Picture Adjust ”
cannot be used when:
– The NET input selector is selected, or
– “ Monitor Out ” is set to “ Sub ” (
➔
pages 55 ).
*1 This procedure can also be performed on the remote controller
by using the Quick Setup (
➔
page 49
).
*2 When a 3D video source is input, “ Wide Mode ” is fixed to
“ Full ”.
*3 When “ Metadata Compatible ” is enabled (
➔
page 61 ),
“ Picture Mode ” is fixed to “ Direct ”.
*4 When the “ Picture Mode ” setting is set to anything other than
“ Custom ”, this setting cannot be used.
*5 If the “ Resolution ” setting is set to “ 4K Upscaling ”
(
➔
pages 55 , 69 ), this setting is fixed at “ Off ”.
*6 Press CLR if you want to reset to the default value.
*7
When the “ Noise Reduction ” setting is set to anything other
than “ Off ”, this setting cannot be selected.
*8 With some TVs, there may be no picture when this setting is
set to “
4K Upscaling ”.
*9 When “ Resolution ” is set to “ 1080p ”, “ 1080p/24 ”, or “ 4K
Upscaling ” while “ Monitor Out ” is set to “ Analog ”, the
video is output in 1080i.
*10 When “ Resolution ” is set to “ 1080p/24 ” or “ 4K Upscaling ”
while “ Monitor Out ” is set to “ Sub ”, the video is output in
1080p.
*11 When “ Resolution ” is set to “ Auto ” while “ Monitor Out ” is
set to “ Analog ”, the video is output as “ Through ”.
Audio Selector
■
Audio Selector
`
ARC :
The audio signal from your TV tuner can be sent to
HDMI OUT MAIN of the AV receiver.
*1
With this selection, the TV’s audio can be
automatically selected as a priority among other
assignments.
`
HDMI :
This can be selected when
HDMI IN
has been
assigned as an input source. If both HDMI ( HDMI
IN ) and digital audio inputs ( COAXIAL IN or
OPTICAL IN ) have been assigned, HDMI input is
automatically selected as a priority.
`
COAXIAL :
This can be selected when COAXIAL IN has been
assigned as an input source. If both coaxial and
HDMI inputs have been assigned, coaxial input is
automatically selected as a priority.
`
OPTICAL :
This can be selected when
OPTICAL IN
has been
assigned as an input source. If both optical and HDMI
inputs have been assigned, optical input is
automatically selected as a priority.
`
Analog :
The AV receiver always outputs analog signals.
You can set priorities of audio output when there are both
digital and analog inputs.
Note
• This setting can be made only for an input source that is assigned
to HDMI IN , COAXIAL IN , or OPTICAL IN .
• This setting cannot be used with the NET and USB input
selectors.
• When using the Whole House Mode, “ Audio Selector ” is fixed
to “ Analog ”.
• With the Game2 input selector, “ Analog ” cannot be used.
*1 You can select “ ARC ” if you select the TV/CD input selector.
But you cannot if you’ve selected “ Off ” in the “ Audio Return
Channel ” setting (
➔
page 75 ).