Advanced Operations
En-58
Main Menu
Speaker Setup
Here you can check the settings made by
Audyssey MultEQ XT32 Room Correction and Speaker
Setup function, or set them manually, which is useful if
you change one of the connected speakers after using
Audyssey MultEQ XT32 Room Correction and Speaker
Setup function.
Note
• These settings are not available in either of the following cases:
– a pair of headphones is connected.
– the “
Audio TV Out
” setting is set to “
On
” (
➔
page 74
).
– “
HDMI Control(RIHD)
” is set to “
On
” (
➔
page 74
) and
you’re listening through your TV speakers.
Speaker Settings
If the impedance of any speaker is 4 ohms or more but less
than 6, set the minimum speaker impedance to 4 ohms.
If you bi-amp the front speakers, you must change the
“
Speakers Type (Front)
” setting. For details on speaker
wire connection, see “Bi-amping the Front Speakers”
(
➔
page 14
). When connecting speakers without
crossover network, you need to change the “
Speakers
Type (Front)
” setting beforehand. For details on
connection, refer to “Using Speakers Without Crossover
Network” (
➔
page 15
).
Note
• When bi-amping is used, the AV receiver is able to drive up to 5.1
speakers in the main room.
• Before you change these settings, turn down the volume.
■
Speaker Impedance
`
4ohms
:
Select if the impedance of any speaker is 4 ohms or
more but less than 6.
`
6ohms
:
Select if the impedances of all speakers are between 6
and 16 ohms.
■
Speakers Type (Front)
`
Normal
:
Select this if you’ve connected your front speakers
normally.
`
Bi-Amp
:
Select this if you’ve bi-amped your front speakers.
`
Digital Crossover
:
Select this if you’re using speakers without crossover
network.
Tip
• If “
Speakers Type (Front)
” is set to “
Digital Crossover
”, a
confirmation screen appears. Select “
Next (2-7. Digital
Processing Crossover Network)
” to display the screen for
Digital Processing Crossover Network (
➔
page 62
). Continue
with the settings.
■
Powered Zone 2, Powered Zone 3
`
No
`
Yes
:
Zone 2/3 speakers can be used. (Powered Zone 2/3
enabled).
■
Preout to External Amplifier
`
No
`
Surr Back
,
Front High
,
Front Wide
For 9.1-channel playback, select the channel output by
SB/FH/FW EXT AMP
jacks. If you select speakers whose
setting in Speaker Configuration is set to “
None
”, it will be
automatically switched to “
80Hz (THX)
”.
Note
• If the “
Speakers Type (Front)
” setting is set to “
Bi-Amp
” or
“
Digital Crossover
”, Powered Zone 2 cannot be used.
• When the “
Powered Zone 2
” setting is set to “
Yes
” and Zone 2
is turned on, the surround back and front high speakers cannot be
used.
• If the “
Powered Zone 2
” setting is set to “
No
”, the “
Powered
Zone 3
” setting cannot be selected.
• “
Preout to External Amplifier
” is not available in either of the
following cases:
– The “
Speakers Type (Front)
” setting is set to “
Bi-Amp
” or
“
Digital Crossover
”.
– The “
Powered Zone 2
” setting is set to “
Yes
”.
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify “
Full Band
” for speakers that can output low
frequency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover
frequency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies. If you set up your
speakers using Audyssey MultEQ XT32 Room Correction
and Speaker Setup, please make sure manually that any
THX speakers are set to “
80Hz(THX)
” crossover.
■
Subwoofer
`
Yes
`
No
Speaker Setup
Some of the settings in this section are set automatically
by Audyssey MultEQ
®
XT32 Room Correction and
Speaker Setup (
➔
page 35
).
If you change these settings, you must run
Audyssey MultEQ XT32 Room Correction and
Speaker Setup again (
➔
page 35
).
1 2 3 4
5
“
Setup
”
This setting is set automatically by
Audyssey MultEQ
®
XT32 Room Correction and
Speaker Setup (
➔
page 35
).
Содержание DTR-50.4
Страница 1: ...AV Receiver DTR 50 4 Instruction Manual ...
