background image

Customer Services (858) 578-7887 & (888) GO IN

TEC

IN

TEC

 Controls, 12700 Stowe Dr., Suite 1

0

0, Poway, CA 92064

Fax (858) 578-4633 & (888) FX IN

TEC

www.inteccontrols.com

Specification subject to change without notice.

Printed in USA 140403

April 03, 2014 – 

Revision

Polygard® is a registered trademark of MSR

GAADT531193_E_1011.pdf

PolyGard



AT-1193

 

Electrochemical Chlorine Transmitter 

Serial No. AT03-005

 

User Manual

 

October 2011 

Specifications subject to change without notice. | USA 140403 | Page 1 of 13

12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN

TEC

 | relevantsolutions.com/inteccontrols

AT-1193 – UserManual

Polygard® is a registered trademark of MSR | GAADT531193_E_1011.pdf

12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN

TEC

 | relevantsolutions.com/inteccontrols

PolyGard

®

 is a registered trademark of MSR-Electronic GmbH | GAADT531193_E_1011

January 04, 2016 – 

Revision

INTEC Controls | 12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.INTEC | inteccontrols.com

February 11, 2020 – 

Revision

Содержание AT03-005














Отзывы: