INSYS EDGE 5.0 Series Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 107

background image

INSYS GPRS/EDGE 5.0 serial

Functions

71

6.8

Remote Configuration

During a CSD or “TCP transparent” data connection, the INSYS
GPRS/EDGE 5.0 serial can be switched to remote command mode
by entering the escape sequence via the data connection from
the remote terminal.

Note: After the 4 escape characters were entered at the local de-

vice (1 second pause before and after the entry, no re-
turn -

<CR>

-), the remote configuration at the remote

terminal is activated. The data connection is main-
tained in the background. The 4 escape characters must
be entered within 1 second.

If this was configured, the configuration password is queried be-
fore the switching to the remote command mode occurs.

Note: See also Chapter

6.1.1

- Password Protection

After the escape sequence is detected, the prompt for entering
the password appears.

If no valid password is entered within 30 seconds (attention:
complete the entry with line end character), the configuration
mode will be exited with the following message

A valid password is acknowledged with

OK

; now the

AT

com-

mands released for remote configuration can be entered.

Terminate configuration

Note:

Due to the sometimes long packet run times for TCP
connections, the escape character **** must be sent in

one

TCP packet. Otherwise the pauses between the in-

dividual characters get too large and the reception of
the sequence is terminated.

<pause>

****

<pause>

CONFIG
PASSWORD:

ERROR

OK

AT**EXIT

6.9

Firmware Update

The firmware of the

µ

controller can be loaded locally (via the serial

interface), and remote (CSD or "TCP transparent" connection).

Before the firmware is updated, hardware handshake must
always be activated ((INSYS GPRS/EDGE 5.0 serial and re-
mote terminal).

The process is started. The device prepares itself for receiving the
new firmware.

AT**FLASH

Send *.HEX
file now

«
...
69
70
71
72
73
...
»

Содержание EDGE 5.0 Series












































































































Отзывы:

Нет отзывов

Похожие инструкции для EDGE 5.0 Series

Leroy-Somer R180

Бренд: Nidec Страницы: 20

Бренд: ZIMO Страницы: 38

SmartSwitch 6000

Бренд: Cabletron Systems Страницы: 76

Бренд: IBM Страницы: 276

Бренд: IBM Страницы: 32

Бренд: IBM Страницы: 157

Tissue-Tek TEC 6

Бренд: Sakura Seiki Страницы: 6

Бренд: ValvTechnologies Страницы: 20

Бренд: GEA Страницы: 47

Бренд: M-system Страницы: 3

Бренд: M-system Страницы: 10

Бренд: Z-Wave Страницы: 44

HydroGuard 1430 Series

Бренд: Powers Страницы: 8

Бренд: Danfoss Страницы: 14

Бренд: Rauch Страницы: 85

Бренд: Ulvac Страницы: 48

Бренд: IFM Страницы: 7

Бренд: WANDERS Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды