manualshive.com logo in svg

INIM Electronics Sol Series, Руководство по установке, Страница: 5 / 40

Поделиться
Скачать
INIM Electronics Sol Series Скачать руководство пользователя страница 5

Installation manual

About this manual

5

About this manual

MANUAL CODE

DCMIINE0SOLE

REVISION

1.00

0-1

Terminology

CONTROL PANEL, 

SYSTEM, DEVICE

The main control unit or any constituent part of the Sol intrusion control system.

LEFT, RIGHT, 

BEHIND, ABOVE, 

BELOW

Directions as seen by the operator when directly in front of the mounted device.

QUALIFIED 

PERSONNEL

Persons whose training, expertise and knowledge of the products and laws regarding security

systems, are able to create, in accordance with the requirements of the purchaser, the most

suitable solution for the premises to be protected.

SELECT

Click on a specific item on the interface (drop-down menu, options box, graphic object, etc.).

PRESS

Click-on/push a video button/key on a keypad or screen.

0-2

Graphic conventions

Note

The notes contain important information relating to the text.

ATTENTION!

The attention prompts indicate that total or partial disregard of the procedure could damage
the device or its peripherals.

DANGER!

The DANGER warnings indicate that total or partial disregard of the procedure could injure the
operator or persons in the vicinity.

Содержание Sol Series









































Отзывы:

Нет отзывов