INIM Electronics Sol Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 40

INIM Electronics Sol Series Скачать руководство пользователя страница 15

Installation manual

The control panel and peripherals

15

2-3

Accessory modules for

connectivity

Sol control panels allow the use of accessory modules in order to increase the already

available functions.
These are modules, for installation directly inside the control panel enclosure via the allocated

connectors, which interface with the control panel in addition to the on-board USB port, via

other communication channels.
•

Sol-3G

GSM/GPRS interface

•

Sol-WIFI

LAN WiFi interface

•

Sol-LAN/S

LAN Ethernet interface

•

Sol-PSTN

PSTN interface

•

SmartLogos30M

Voice board

2-3-1

Sol-3G, GSM communicator module

The optional Sol-3G module is a device that interfaces control panels with mobile network

communication channels (2G, GPRS, 3G).
The functions available for duly equipped Sol control panels are:
• voice calls via the SmartLogos30M voice board installed on the control panel
• digital calls via CONTACT-ID protocols
• transmission of SIA-IP events
• sending of SMS texts for each event using alternatively:

- the description provided by the events log
- a customizable description

• commands sent by the user via SMS
• commands using recognition of user's telephone number (CALLER-ID)
• answerphone function
• connection to INIM Cloud services

When the control panel enclosure is closed, these LEDs will be Off.

Table 2-12: Sol 3G - technical specifications

Antenna

dipole GSM-UMTS, SMA-Male connector (impedance 50Ohm)

Frequency

2G (GSM/GPRS)

Quad band (850/900/1800/1900 MHz)

3G (UMTS/HSPA)

World wide (800/850/900/1900/2100 MHz)

Maximum RF output power

2W @ 1W

Temperature

from -10° to +40° C

Maximum humidity

75% (without condensation)

Environmental class

II

IP Protection grade

30

Dimensions

51 x 138 x 21 mm

Weight

61g

Table 2-13: LED signalling

LED

function

ON

OFF

COM

GSM communica-

tions

Indicates an ongoing GSM

communication

This LED lights during ongoing GSM communications

(voice calls, ARC calls, emergency calls, sending of SIA-

IP data packets, sending of SMS texts)

Not communicating

BUS

Communication over

BUS

Indicates communication

with the control panel

The LED blinks during ongoing communications

Not communicating

NET

Connection

Indicates the status of the

wireless network

Slow flashing (ON 64ms / OFF 3000 ms) - device regis-

tered to the cellular network

Device Off

Regular flashing (ON 64ms / OFF 800 ms) - device not

registered and in search of the network provider

Fast flashing (ON 64ms / OFF 300 ms) - data communi-

cation in progress

«
...
13
14
15
16
17
...
»

Содержание Sol Series









































Отзывы:

Нет отзывов