manualshive.com logo in svg

INIM Electronics Sol Series, Руководство по установке, Страница: 34 / 40

Поделиться
Скачать
INIM Electronics Sol Series Скачать руководство пользователя страница 34

34

Installation

Anti-intrusion control panels

4-7-2

Installing optional internal boards

The installation of 

Sol-WIFI

 and 

SmartLogos30M

 optional boards can be achieved via the

connectors integrated into the PCB.
This operation must be carried out when the mains power supply and battery are

disconnected:

1. Remove all power from the control panel by disconnecting the primary power supply to

the control (230V~).

2. Open the control panel enclosure.
3. Disconnect the backup battery from its connector on the motherboard [

A

].

4. Insert the board into the appropriate connector:

- [

B

], for the Sol-WIFI board, use the appropriate slot

- [

C

], for the SmartLogos30M board

5. Reconnect the backup battery.
6. Close the control panel.
7. Power up the control panel by reconnecting the mains power supply (230V

~

).

4-8

Connecting the Land-line 

(PSTN)

Connect the land line to the PSTN terminals on the Sol-PSTN module (

Table 2-18: Sol PSTN -

description of parts, A

).

Note

If an ADSL line is present, it is necessary to connect the control panel downstream of the ADSL filter on

the line dedicated to telephone equipment (this line is clearly indicated on the filters).

If the control panel is not equipped with a SmartLogos30M voice board, voice calls will

produce a continuous beep for 30 seconds.
All the functions of the Sol control panel that use the PSTN line (voice dialer, answerphone,

alarm receiving centre and teleservice) can be managed completely over the GSM network by

the Sol-3G module.

Sol-PSTN

Содержание Sol Series









































Отзывы:

Нет отзывов