background image

2

Power supply stations

Warranty

INIM Electronics s.r.l. (Seller, Our, Us) warrants the original purchaser that this

product shall be free from defects in materials and workmanship under normal

use for a period of 24 months. As INIM Electronics s.r.l. does not install this

product directly, and due to the possibility that it may be used with other

equipment not approved by Us; INIM Electronics s.r.l. does not warrant against

loss of quality, degradation of performance of this product or actual damage that

results from the use of products, parts or other replaceable items (such as

consumables) that are neither made nor recommended by INIM Electronics. Seller

obligation and liability under this warranty is expressly limited to repairing or

replacing, at Seller's option, any product not meeting the specifications. In no

event shall INIM Electronics s.r.l. be liable to the purchaser or any other person for

any loss or damage whether direct or indirect or consequential or incidental,

including without limitation, any damages for lost profits, stolen goods, or claims

by any other party caused by defective products or otherwise arising from the

incorrect or otherwise improper installation or use of this product.
This warranty applies only to defects in parts and workmanship relating to normal

use. It does not cover:

damage arising from improper maintenance or negligence

damage caused by fire, flood, wind or lightning

vandalism

fair wear and tear

INIM Electronics s.r.l. shall, at its option, repair or replace any defective products.

Improper use, that is, use for purposes other than those mentioned in this manual

will void the warranty. Contact Our authorized dealer, or visit our website for

further information regarding this warranty.

Limited 

warranty

INIM Electronics s.r.l. shall not be liable to the purchaser or any other person for

damage arising from improper storage, handling or use of this product.
Installation of this Product must be carried out by qualified persons appointed by

INIM Electronics. Installation of this Product must be carried out in accordance

with Our instructions in the product manual.

Copyright

The information contained in this document is the sole property of INIM

Electronics s.r.l. No part may be copied without written authorization from INIM

Electronics s.r.l.
All rights reserved.

European 

Directive 

compliance

Moreover, INIM Electronics s.r.l. also declares that all other devices mentioned in

this manual are in compliance with the essential requirements and other relevant

provisions of Directives 2014/35/UE and 2014/30/UE.
The full declarations of conformity can be found at www.inim.biz

Note to the 

installer

In order to provide adequate protection and instructions for proper use, you (the

installer) should be familiar with the operating procedure of this device. As the

only individual in contact with system users, it is your responsibility to instruct

them on how to use this device properly.

Technical 

support

Our professional engineers are readily available to assist you. Call us, and you will

be connected right away to a person who will answer all your questions and

provide you with full technical support.

Содержание SmartLevel Series





















Отзывы: