Ingersoll-Rand Intellisys SSR 10-40, Руководство для обслуживающего персонала

Страница: 66 / 107

-63- -64-
PSIA PSI INCHES MM INCHES
VACUUM MERCURY MERCURY WATER
4.5 10.2 20.77 527.49 282.85
4.4 10.3 20.97 532.66 285.62
4.3 10.4 21.17 537.83 288.39
4.2 10.5 21.38 543.00 291.16
4.1 10.6 21.58 548.17 293.94
4 10.7 21.79 553.34 296.71
3.9 10.8 21.99 558.52 299.48
3.8 10.9 22.19 563.69 302.26
3.7 11 22.40 568.86 305.03
3.6 11.1 22.60 574.03 307.80
3.5 11.2 22.80 579.20 310.58
3.4 11.3 23.01 584.37 313.35
3.3 11.4 23.21 589.45 316.10
3.2 11.5 23.41 594.72 318.89
3.1 11.6 23.62 599.89 321.67
3 11.7 23.82 605.06 324.44
2.9 11.8 24.02 610.23 327.21
2.8 11.9 24.23 615.40 329.99
2.7 12 24.43 620.57 332.76
2.6 12.1 24.64 625.74 335.53
2.5 12.2 24.84 630.92 338.31
2.4 12.3 25.04 636.09 341.08
2.3 12.4 25.25 641.26 343.85
2.2 12.5 25.45 646.43 346.62
2.1 12.6 25.65 651.60 349.40
2 12.7 25.86 656.77 352.17
1.9 12.8 26.06 661.94 354.94
1.8 12.9 26.26 667.12 357.72
1.7 13 26.47 672.29 360.49
1.6 13.1 26.67 677.46 363.26
1.5 13.2 26.88 682.63 366.04
1.4 13.3 27.08 687.80 368.81
1.3 13.4 27.28 692.97 371.58
1.2 13.5 27.49 698.14 374.35
1.1 13.6 27.69 703.32 377.13
1 13.7 27.89 708.49 379.90
0.9 13.8 28.10 713.66 382.67
0.8 13.9 28.30 718.83 385.45
0.7 14 28.50 724.00 388.22
0.6 14.1 28.71 729.17 390.99
0.5 14.2 28.91 734.34 393.77
0.4 14.3 29.11 739.52 396.54
0.3 14.4 29.32 744.69 399.31
0.2 14.5 29.52 749.86 402.08
0.1 14.6 29.73 755.03 404.86
0 14.7 29.93 760.20 407.63
THE INTELLISYS CONTROLLER DISPLAYS INLET VACUUM IN PSI VAC-
UUM. FOR INSTANCE, IF THE INLET VACUUM DISPLAY READS 128, THIS
IS 12.8 PSI VACUUM. FOR THOSE OF YOU WHO ARE USED TO OTHER
SCALES SUCH AS “H
2
0" OR "HG" WE HAVE INCLUDED THE ABOVE
CONVERSION CHART.
50-200 HORSEPOWER ROTARY
INTELLISYS EQUIPPED
INTELLISYS UNITS WITH AN E-PROM LABELED “SHOW”
The purpose of the “Show” software is to demonstrate the display functions of
the Intellisys controller.
Attached are the instructions which outline the procedure for using the “show”
prom. Only the Display Select Up and Down buttons work when the E-Prom is
in a controller. The instructions 1-7 also apply to any E-Prom installation.
The “Show” prom should not be in any compressor delivered to a customer.
It has been determined that after the “show” prom is used some problems may
occur with the set point values:
a) The set point values may change and have to be reset.
b) The set point routine may not function correctly. This means that
the correct values may not be obtainable.
To correct the problem, do one of the following:
a) Remove the RAM chip, then put it back into the board.
CAUTION: Doing this will cause the run and loaded hours to be
lost.
Preferred Correction:
b) Replace your current E-Prom with an E-Prom of the next higher
Rev. level. (Contact Customer Service for current revision level
E-Prom.)
SSR 50-200 “SHOW PROM”
INSTALLATION INSTRUCTIONS
1. Disconnect all power, lock and tag out the main disconnect.
2. Open Starter Box Door.
3. Remove the back cover of the Intellisys panel mounted in the starter door
(top section).
4. Locate the production prom installed in the U2 socket.