Ingersoll-Rand ARO EVO EP20 Series Скачать руководство пользователя страница 21

Страница: 21 / 44

EP20-XXXXX-XXX-XXX (en)

Page 21 of 44

Leak Detector Safe Loop Calculations

Leak Detector

Cable

Zener Barrier

IR Part Number 96270-2

Alpha Wire 1173C

IR Part Number 97414

Ui = 32 VDC

Uo = 25.2 VDC

Ii = 87 mA

Io = 74 mA

Pi = 0.616 W

Po = 0.464 W

Ci = 0.052 uF

Cc 0.055uF

Co = 0.107 uF

Li = 3.7 uH

Lc 6.488mH

Lo = 6.492 mH

Um = 250 VAC/DC

Ta = -18oC To +80oC

Ta = -40

C To +60

Ui ≥ Uo (32 V > 25.2 V)

Ii ≥ Io (87 mA > 74 mA)

Pi ≥ Po (0.616 W > 0.464 W)
Maximum Cable Capacitance Cc = Co-Ci ≥ 0.107 uF - 0.052 uF = 0.055 uF

Maximum Cable Inductance Lc = Lo-Li ≥ 6.492 mH - 0.0037 mH = 6.488 mH
As per cable manufacturer Alpha Wire, Cable Capacitance = 33PF/FT, Cable Inductance = 0.00018 mH/FT

Maximum cable run length = 359 feet

Calculated Cable Capacitance = 11.8 nF < 0.055 uF

Calculated Cable Inductance = 6.48 mH < 6.462 mH

7.3.2 Thermal Protection - Hazardous Motor

CAUTION

Do not connect the "Logic Out" (Pin 10) from MCB 112 card to VFD digital input pin 33. The

digital inputs on the VFD are configured for NPN and are not compatible with the logic out from the PTC

thermistor card.



The hazardous motor is installed with 3 PTC thermal sensors in series. It is required to wire the PTC sensors to terminals T1

and T2 on the MCB 112 PTC thermistor card installed in the option A slot of the VFD. This card comes pre-installed when

the hazardous VFD option is ordered.



Ensure T37 (Safe Stop) from MCB 112 Thermistor card is wired to pin 37 on VFD as shown below. If an emergency stop is in-

stalled on this unit (recommended), it will need to be wired in series between these terminals as shown. Additionally, when

and emergency stop is in series with the output of the PTC thermistor card, the Safe Torque Off digital input (pin 37) can be

tripped by either the PTC thermal sensor or the E-stop (Alarm 68).



Please note that the option A slot is not available for fieldbus communication card options for hazardous duty pump con-

figurations.

PTC

M 3~

12 13 18 19 27 29 32 33 20 37

MS 220 DA

Code No. 130B1137

Motor protection

SEE MANUAL FOR

MCB 112 PTC Thermistor Option B

ADDITIONAL INSTRUCTIONS.

PTB 14 ATEX 3012U

CAUTION:

II (2) G [Ex e] [Ex d] [Ex n]

10 mA
60 mA

20-28 VDC
20-28 VDC

II (2) D [Ex tb][Ex tc]

0102

12030-1201-03

.com

X44

T1 T2 NC NC NC NC NC NC NC

LOGIC

SAFE STOP

OUT

T37

10 11 12

NOTE:

Ensure that the jumper wire (from factory) between pins 12 and 37

is removed prior to wiring the thermistor card to pin 37.

Содержание ARO EVO EP20 Series













































Результаты поиска

Содержание ARO EVO EP20 Series

Отзывы:

Похожие инструкции для ARO EVO EP20 Series

Бренды по названию

Популярные бренды

Ingersoll-Rand ARO EVO EP20 Series, Руководство оператора

Результаты поиска

Содержание ARO EVO EP20 Series

Отзывы:

Похожие инструкции для ARO EVO EP20 Series

Бренды по названию

Популярные бренды