53
Appendix I System Alarm Programming
The System Alarm Programming of V2040 involves the following
three procedures:
1.
Alarm Contact/Camera Programming;
2.
Alarm Contact/Monitor Programming;
3.
Monitor Arming.
Alarm Contact/Camera Programming
SYSTEM
1 SET TIME AND DATE
2 SET SYSTEM TOURS
3 SET SYSTEM SALVOS
4 SET EVENT TIMERS
5 SET ALARM CONTACTS
6 MONITOR STATUS
RETURN MAIN
ALARM CONTACT SETUP
PREVIOUS MENU
ACN
0001
0002
0003
0004
0005
0006
0007
0008
CAM
0001
0002
0003
0004
0005
0006
0007
0008
PRE
000
000
000
000
000
000
005
000
AUX
0-
0-
0-
0-
0-
0-
1-ON
0-
CN
N
N
N
N
N
N
Y
N
DWL
02
02
02
02
02
02
30
00
ALARM CONTACT SETUP
PREVIOUS MENU
ACN
0002
0003
0004
0005
0006
0007
0008
SITE
---
---
---
---
---
---
---
RACN
TE
Page
Right
----
----
----
----
----
----
----
--N:---
--N:---
--N:---
--N:---
--N:---
--N:---
--N:---
0001 002 01Y:024 0001
Select the ALARM CONTACT SETUP sub-menu from the
SYSTEM menu, and define alarm contact to camera associations.
1.
Locate the cursor in the CAM entry with the desired Alarm
Contact Number (ACN);
2.
Enter the desired Camera Number (1~1024) or Pseudo Number
on the keypad;
3.
Press the ACK key to confirm. The entered Camera Number will
be displayed in the entry.
Alarm Contact/Monitor Programming:
ACCESS
1 KEYBOARD/MONITOR
2 KEYBOARD/CAMERA VIEW
3 KEYBOARD/CAMERA CTRL
4 MONITOR/CAMERA ACCESS
5 MONITOR/CONTACT ACCESS
6 KEYBOARD/REMOTE SITE
RETURN MAIN
MON CONTACT TABLE - -
PREVIOUS MENU
MONITOR
ACN
0001
0002
0003
0004
0005
0006
0007
0008
01
N
N
N
N
N
N
N
N
02
N
N
N
N
N
N
Y
N
03
Y
N
N
N
N
N
N
N
04
N
Y
Y
N
N
N
N
N
Select the MONITOR/CONTACT ACCESS sub-menu from the
ACCESS menu, and associate alarm contacts with the desired
monitors.
1.
Locate the cursor in the desired Monitor entry;
2.
Use the ACK key to toggle between "N" and "Y" (N = Disabled,
Y = Enabled);
3.
Repeat Steps 1 and 2 until all the desired entries are defined;
4.
Move the cursor to the PREVIOUS MENU line, and press the
ACK key to return to the ACCESS menu.
For more details, please refer to
Section 5.7.6
.
Arming the Monitors:
To arm a monitor:
1.
Place the key switch in the PROGRAM position;
2.
Enter the desired Arming type Code on the keypad;
3.
Press the ARM key to arm the monitor;
4.
Place the key switch in the OPERATE position.
Appendix II ASCII / HEX System Control
Codes
Command
ASCII HEX
RUN SEQ
S
53
CAM
HOLD
H
48
NEXT CAM
+
2B
CAMERA
#
23
MONITOR
M
4D
PAN
LEFT
L
4C
PAN
RIGHT R
52
TILT UP
U
55
TILT
DOWN
D
44
CALL SHOT
\
5C
FOCUS
FAR
F
46
FOCUS
NEAR
N
4E
IRIS CLOSE
C
43
IRIS OPEN
O
4F
LENS WIDE
W
57
LENS
TELE T
54
AUX
OFF
J 4A
LOCKOUT K
4B
MON
ARM [ 5B
MON
DISARM
] 5D
ALARM
NEW
E
45
ALARM
CLEAR I 49
ALARM
OLD
G
47
ACK
_
5F
PROGRAM
P
50
SET SHOT
^
5E
ID BLINK
*
2A
ID INC
,
2C
ID DEC
-
2D
ID LEFT
.
2E
ID RIGHT
/
2F
ID
BLINK
：
3A
ID INC
<
3C
ID DEC
=
3D
ID LEFT
>
3E
ID RIGHT
?
3F
ZERO
0
30
ONE
1
31
TWO
2
32
THREE
3
33
FOUR
4
34
FIVE
5
35
SIX
6
36
SEVEN
7
37
EIGHT
8
38
NINE
9
39
ASCII Codes for System Control Terminal
Command
ASCII HEX
KBD1
a
61
KBD2
b
62
KBD3
c
63
KBD4
d
64
Er (Enter)
OD
