Immergas HERCULES SOLAR 26 1A Скачать руководство пользователя

Страница: 67 / 68

STHSC ed 0710

HERCULES Solar 26 1A

Technical Documentation

230 VAC are present on the L-N terminals of the zones control unit

(green LED H11 on with fixed light).

Check the electric power supply upstream from the zones control unit

and restore it.

Yes

The connection between the zones digital control unit and boiler

P.C.B. (clamps 41-44) is OK

Restore the IMG BUS connection.

See error section 36

Yes

The zones digital control unit is configured correctly ( S25 S26 S27

selectors positions as per instruction book).

Restore the correct configuration of the selectors

Yes

Check the presence and effective request of the room thermostats of the respective zones. If the problem persists, replace the zones digital control unit.

230 VDC are present to the clamps 1-3 of connector X11 on the

boiler P.C.B.

Check the electric power supply of the boiler P.C.B. and replace it if

necessary.

Yes

230 VDC are present to the clamps 1-2 of connector X11 on the

pump relay board.

Replace the anti-jamming filter.

Yes

230 VDC are present to the clamps 1-2 of connector X2 on the

pump relay board.

N.B.: Check current continuity between clamp 3 of the pump relay board

connector X1 and clamp 1 boiler P.C.B. X1 connector.

Replace the pump relay board

Yes

Release the zone pump by acting on the shaft after having loosened the front cap and replaced it, if necessary.

N.B.: there may be a fixed red light on the pump

If digital zones control unit is used

The connections between zones digital control unit and relative zone

pumps are OK

Check and restore the relative electric connections

Yes

Release the pumps of the respective zones by acting on the shaft after having loosened the front cap and replaced, if necessary.

N.B.: there may be a fixed red light on the pumps

Содержание HERCULES SOLAR 26 1A





































































Результаты поиска

Содержание HERCULES SOLAR 26 1A

Отзывы:

Похожие инструкции для HERCULES SOLAR 26 1A

Бренды по названию

Популярные бренды

Immergas HERCULES SOLAR 26 1A, Руководство пользователя

Результаты поиска

Содержание HERCULES SOLAR 26 1A

Отзывы:

Похожие инструкции для HERCULES SOLAR 26 1A

Бренды по названию

Популярные бренды