Immergas HERCULES SOLAR 26 1A Скачать руководство пользователя страница 62

Страница: 62 / 68

STHSC ed 0710

HERCULES Solar 26 1A

Technical Documentation

ERROR 16

Fan anomaly

24 VDC is present to clamps 1-2 of the connector X7.

Replace the P.C.B.

Yes

The wiring between the P.C.B. and fan is OK.

Restore the electric connection/replace the wiring.

Yes

Replace the fan. If the anomaly persists, replace the P.C.B.

The wiring between the P.C.B. and fan is OK.

Check continuity of the cables on clamps 3-4-5 of the connector x7 No

Restore the electric connection/replace the wiring.

Yes

Replace the fan. If the anomaly persists, replace the P.C.B.

ERROR 20

Parasite flame block

The detection electrode and the relative wiring are integral.

Check/replace detection electrode/replace wiring.

Yes

Replace the P.C.B.

ERROR 23

Return probe anomaly

Breakage of the return probe resistance (the anomaly does not affect boiler

functioning

The resistance (R9) is present on the connector X9 clamps 8-9 of

the P.C.B.

Restore/replace the electric resistance (2.2 kΩ 1/4 W).

Yes

Replace the P.C.B.

ERROR 24

Push button control panel anomaly

The buttons on the control panel function regularly (check that a

"click" is heard when the button is pressed).

Check that there are no keys blocked or jammed under the control panel.

Yes

Replace the display board

ERROR 27

Insufficient circulation

The boiler pump functions correctly.

See section B

Yes

The pump/s functions correctly.

See section G

Yes

Any CH system zone valve or cut-off cocks are open.

Restore circulation in the CH system by acting on the closed devices

and also check:

- the correct functioning of the boiler by-pass;

- the opening times of any zone valve (on requirement it is possible to delay

ignition of the burner by acting on the boiler TIMER RT parameter);

- the correct functioning of any thermostatic valves.

Yes

The NTC flow probe is OK (10 kΩ at 25°C).

Replace NTC probe.

Yes

Check/clean/replace the main heat exchanger (condensation module).

If the anomaly persists, replace the P.C.B.

Содержание HERCULES SOLAR 26 1A





































































Результаты поиска

Содержание HERCULES SOLAR 26 1A

Отзывы:

Бренды по названию

Популярные бренды

Immergas HERCULES SOLAR 26 1A, Руководство пользователя

Результаты поиска

Содержание HERCULES SOLAR 26 1A

Отзывы:

Бренды по названию

Популярные бренды