Immergas HERCULES SOLAR 26 1A Скачать руководство пользователя страница 47

Страница: 47 / 68

STHSC ed 0710

HERCULES Solar 26 1A

Technical Documentation

The boiler is supplied with a control panel

(where the buttons

and temperature selector switches used to control the boiler are

positioned)

and a display that shows appliance functioning

mode and status.

Each key has the following function:

Stand-by - On Button

Summer ( ) and Winter ( ) functioning mode

selection button

COMFORT or SAVING ( )functioning mode

selection button

Reset (RESET) / exit menu (ESC) button

Menu entry (MENU)/ data confirmation button

(OK)

In normal functioning phase the display indicates the

functioning mode.

In the case shown below as an example, the boiler is functioning

to satisfy a room central heating request

During the request for central heating “HEAT.” appears on

the display on the status indicator (6) and at the same time

as burner ignition the flame presence indicator switches on

(8) with relative power scale and the indicator (9 and 7) with

the instantaneous outlet temperature from the primary heat

exchanger at 55° to satisfy the setting of 60° in central heating

mode made by the selector switch (3).

Functioning status and mode.

Содержание HERCULES SOLAR 26 1A





































































Результаты поиска

Содержание HERCULES SOLAR 26 1A

Отзывы:

Бренды по названию

Популярные бренды

Immergas HERCULES SOLAR 26 1A, Руководство пользователя

Результаты поиска

Содержание HERCULES SOLAR 26 1A

Отзывы:

Бренды по названию

Популярные бренды