Immergas HERCULES SOLAR 26 1A Скачать руководство пользователя

Страница: 48 / 68

STHSC ed 0710

HERCULES Solar 26 1A

Technical Documentation

Below find a list of the various boiler functioning status that

appear on the malfunction display by means of the indicator

(6).

Display (6)

Description of functioning states

SUMMER

Summer functioning mode without request in progress.

Boiler in stand-by for domestic hot water request.

WINTER

Winter functioning mode without request in progress.

Boiler in stand-by for domestic hot water or central heating request.

DHW ON

Domestic hot water mode in progress.

Boiler functioning, domestic hot water heating in progress.

CH ON

Central heating mode in progress.

Boiler functioning, central heating in progress.

(ANTIFR.)

Anti-freeze mode in progress.

Boiler functioning to restore the minimum safety temperature against boiler freezing.

CAR OFF

Remote Control

(Optional)

off.

DHW OFF

In the case of use with Super CAR in concomitance with the functioning period in reduced D.H.W. Timer

mode, DHW OFF will appear on the display and indicators 15 and 2 switch off.

(POSTFAN)

Postventilation in progress.

Fan in function after a request for domestic hot water or central heating in order to evacuate residual fumes.

(POSTCIRC)

Postcirculation in progress.

Pump in function after a request for domestic hot water or central heating in order to cool the primary circuit.

P33

(EMERGENCY)

With Remote Control

(Optional)

or room thermostat (TA)

(Optional)

in block mode, the boiler functions all

the same in CH mode

(Can be activated using the “Customisations” menu, it allows to activate the central heating

even if the Remote Control or TA are out of service).

STOP

Reset attempts finished

One hour must pass in order to acquire 1 attempt

(See no ignition block).

ERR xx

Anomaly present with relative error code.

The boiler does not function

(see troubleshooting paragraph).

SET

(DHWSET)

During the rotation of the domestic hot water temperature selector switch, view the state of the adjustment of

the domestic hot water temperature in progress.

SET

(CH SET)

During rotation of the central heating selector switch, view the adjustment status of the boiler flow temperature

for room central heating.

SET

(OTCCORR)

In presence of the external probe

(Optional)

replace the “SET CH” item.

The value that appears is the correction of the flow temperature with respect to the functioning curve set by the

external probe.

(AIRPURGE)

System deaeration in progress.

During this phase, which lasts 18 hours, the boiler pump is started at pre-established intervals, thus allowing

deaeration of the heating system.

(ANTILEG)

Only in the case of use with Super CAR remote control, does it allow to activate the anti-legionella function, which takes

the temperature of the water in the storage tank to 65°C for 15 minutes

(see Super CAR remote control instruction book).

SOLAR

Solar function.

The solar function is activated to control just the pump for DHW.

When the solar pump is powered, the display will show SOLAR’, which may alternate with other function

texts in progress.

SOLAR ON

The solar pump functions permanently.

SOLAR OFF

The solar pump stays off.

Содержание HERCULES SOLAR 26 1A





































































Результаты поиска

Содержание HERCULES SOLAR 26 1A

Отзывы:

Похожие инструкции для HERCULES SOLAR 26 1A

Бренды по названию

Популярные бренды

Immergas HERCULES SOLAR 26 1A, Руководство пользователя

Результаты поиска

Содержание HERCULES SOLAR 26 1A

Отзывы:

Похожие инструкции для HERCULES SOLAR 26 1A

Бренды по названию

Популярные бренды