Immergas HERCULES SOLAR 26 1A Скачать руководство пользователя страница 13

Страница: 13 / 68

STHSC ed 0710

HERCULES Solar 26 1A

Technical Documentation

Central heating circuit

HERCULES Solar 26 1A functioning with 1 pump (Zone 1)

(standard configuration)

Following a central heating type request, the P.C.B. starts the

boiler pump (2), powers the central heating pump (4) and

powers the electric 3-way valve motor (3) causing it to shift

to the central heating position.

In this way the passage towards the storage tank coil is closed

and that towards the hydraulic manifold is opened (1), into

which the water from the primary circuit is introduced.

The hot water is introduced directly into the system through

the flow (MA1) and return (RA1) pipes via the central heating

pump (4).

Thanks to functioning with the two pumps (2 and 4) and

the use of an open hydraulic manifold (1) the water flow rate

and the head available are particularly high

(see flow rate/head

graphics).

FLOW

COILS

STORAGE TANK UNIT

RETURN

COILS

STORAGE TANK UNIT

RA1

MA1

Содержание HERCULES SOLAR 26 1A





































































Результаты поиска

Содержание HERCULES SOLAR 26 1A

Отзывы:

Бренды по названию

Популярные бренды

Immergas HERCULES SOLAR 26 1A, Руководство пользователя

Результаты поиска

Содержание HERCULES SOLAR 26 1A

Отзывы:

Бренды по названию

Популярные бренды