10
English
pressed), use the button
or
(5) to set
the channel group .
Note:
If the digits stop flashing before the group
has been set, press the button SET again .
c) To set the channel number, press the button
SET repeatedly until the digits for CHANNEL
start flashing .
d) Use the button
or
to set the channel
number . The channel setting will be saved as
soon as the digits stop flashing .
3) If the antenna symbol appears on the left or on
the right of the display while the wireless micro-
phone is still switched off, interfering signals or
signals from another wireless system are received .
In this case, set a different channel .
4) Switch on the wireless microphone and point
the infrared sensor of the wireless microphone
towards the IR LED (6) of the receiver (see
instruction manual of the wireless microphone,
if required) . The distance must not exceed 1 .5 m
and there must be no obstacles between the
sensor and the IR LED .
Briefly press the button ACT (7) . The display
backlight of the wireless microphone is activated;
the wireless microphone and the receiver are set
to the same channel .
5) After the receiver and the wireless microphone
have been set to the same transmission channel,
the antenna symbol appears on the left or on
the right of the display of the receiver (symbol on
the left = left antenna receives the most powerful
signal) . If no antenna symbol appears, please
check:
1 . Are the batteries of the wireless microphone
discharged?
2 . Are there any metal objects interfering with
reception in the transmission path?
3 . Is it possible to improve the reception quality
by turning the receiving antennas?
4 . Is the distance between the receiver and the
wireless microphone too long?
5 . Is the interference suppression adjusted with
the control SQUELCH (11) too high? (chap-
ter 4 .4)
4.3 Setting the line output level
To match the output level of the jack LINE OUT (12)
to the input of the subsequent unit:
1) Switch on the subsequent audio unit or advance
the corresponding control of the mixer .
2) Press the button SET three times so that the
numerals for VOL start flashing .
3) Speak / sing into the microphone . While the nu-
merals keep flashing (a few seconds after press-
ing the button SET,
or
), set the output
level with the button
or
(5) [setting range
00 – 63] .
Note:
If the numerals stop flashing before you have
set the output level, press the button SET three times
again .
4) Once the numerals stop flashing, the setting has
been stored .
4.4 Setting the interference suppression
With the control SQUELCH (11), adjust the threshold
value for response of the interference suppression .
The interference suppression will mute the receiver
during pauses in speech or vocals when interfering
signals are received and their levels are below the
threshold value adjusted . A high threshold value,
however, will also reduce the range of the micro-
phone system: If the power of the radio signal falls
below the threshold value adjusted, the receiver is
also muted . Therefore, adjust a high threshold value
(turn the control towards MIN) when the reception
is good and a low value (turn the control towards
MAX) when the distance between the transmitter
and the receiver is long .
5 Specifications
Carrier frequencies: . . . . . 672 .000 – 696 .975 MHz
channels: see table on
pages 24 / 25
RF S / N ratio: . . . . . . . . . . 105 dB
Audio frequency range: . 30 – 18 000 Hz
Dynamic range: . . . . . . . . 100 dB
THD: . . . . . . . . . . . . . . . . < 0 .5 %
Audio outputs
MIC OUT: . . . . . . . . . . 25 mV, 600 Ω, XLR, bal .
LINE OUT: . . . . . . . . . . 350 mV, 600 Ω,
6 .3 mm jack, unbal .
Power supply: . . . . . . . . . via power supply unit
provided and con-
nected to 230 V/ 50 Hz
Ambient temperature: . . 0 – 40 °C
Dimensions (W × H × D): 212 × 45 × 180 mm
Weight: . . . . . . . . . . . . . 930 g
Subject to technical modification .
All rights reserved by MONACOR
®
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may be
reproduced in any form or by any means for any commercial use.
