19
English
6.4 Temperature indication and
overheat control
The spotlight is equipped with an overheat control .
When the temperature inside the spotlight is too
high, the spotlight will be switched off . After cool-
ing down, the spotlight will be switched on again
automatically . To indicate the inside temperature:
1) Press the button MENU repeatedly until the dis-
play indicates
.
2) Press the button ENTER .
3) When
is indicated, press the button ENTER .
The inside temperature will be indicated in °C .
4) To exit the menu branch, press the button MENU .
6.5 Resetting the spotlight
to its factory settings
The factory settings of the spotlight are as follows:
Function
Factory setting
number of DMX channels
= 10 channels
max . brightness
= 100 %
white balance function
subaddress function
slow LED response
= slowest
subaddress
01
11 shades of white
factory settings
white balance
R = 255, G = 255,
B = 255
DMX / independent mode or
slave mode
= DMX / inde-
pendent operation
To reset the spotlight to its factory settings:
1) Press the button MENU repeatedly until the high-
est menu level has been reached .
2) Press the button UP or DOWN repeatedly until
the display indicates
.
3) Press the button ENTER . The display changes to
,
,
,
,
or
.
4) Press the button UP or DOWN repeatedly until
the display indicates
.
5) Press the button ENTER so that the display indi-
cates four entry positions ( . . . .) . Then press the
following buttons:
UP, DOWN, UP, DOWN .
Each time one of these buttons is pressed, an
asterisk ( ) will appear on the display .
6) To reset the settings, press the button ENTER (the
display briefly indicates
) or, to cancel the
procedure, press the button MENU .
7) To be able to control the spotlight by DMX, use
the button MENU to return to the highest menu
level . For an independent operation, use the but-
ton MENU to select the operating mode and then
press ENTER to activate the mode selected .
7 Cleaning the Spotlight
Clean the plastic filter in front of the LEDs at regular
intervals or as required . This is the only way to ensure
that light will be radiated at maximum brightness .
Before cleaning, disconnect the mains plug from
the socket.
Only use a dry, soft cloth and a mild
detergent . Then carefully wipe the plastic filter dry .
For cleaning the other parts of the housing, only
use a dry, clean cloth . Never use any fluid, it may
leak into the spotlight and damage it .
8 Specifications
Data protocol: . . . . . . . . . . DMX 512
Number of DMX channels: selectable:
3, 4, 5 or 10
Light source: . . . . . . . . . . . RGB COB LED
Power consumption
PARC-56 / RGB: . . . . . . 50 W
PARC-64 / RGB: . . . . . . 100 W
Beam angle: . . . . . . . . . 60°
Power supply: . . . . . . . . . . 230 V/ 50 Hz
Power consumption
PARC-56 / RGB: . . . . . . . . 60 VA max .
PARC-64 / RGB: . . . . . . . . 110 VA max .
Dimensions
PARC-56 / RGB: . . . . . . . .
⌀
185 mm × 210 mm
PARC-64 / RGB: . . . . . . . .
⌀
220 mm × 260 mm
Weight
PARC-56 / RGB: . . . . . . . . 2 .4 kg
PARC-64 / RGB: . . . . . . . . 2 .9 kg
Subject to technical modification .
All rights reserved by MONACOR
®
INTERNATIONAL GmbH &
Co. KG. No part of this instruction manual may be reproduced
in any form or by any means for any commercial use.
