14
English
5) To change a setting, press ENTER after you have
selected a storage location . The display now
indicates , , and a number (0 – 255) .
= brightness of the colour red
= brightness of the colour green
= brightness of the colour blue
6) Use the button ENTER to select the colours one
after the other, and use the button UP or DOWN
to set their brightness .
7) To select another shade of white or to change
the settings of another storage location, press the
button MENU so that the number of the storage
location is shown again . Then repeat steps 4 – 6 .
Note:
If the spotlight is switched off and on again in this
mode, the spotlight will remain dark and the shade of white
desired or the individual shade of colour will have to be
selected again .
5.1.3 Music control
The spotlight is equipped with a microphone to
support music-controlled colour changes and a
music-controlled stroboscope .
1) Press the button MENU repeatedly until the high-
est menu level has been reached .
2) Press the button UP or DOWN repeatedly until
the display indicates
.
3) Press the button ENTER . The display indicates the
mode most recently selected:
= music-controlled colour change
= music-controlled stroboscope
4) Use the button UP or DOWN to select the mode
desired .
Important:
Do not exit the menu item
or
via the button MENU if the spotlight is to
operate in a music-controlled mode after switch-off
and switch-on .
5.1.4 Show programmes and sequences of scenes
10 show programmes (
…
) are stored in
the spotlight . Furthermore, 10 se quences of scenes
(
…
) with up to 30 scenes can be pro-
grammed (
☞
chapter 5 .1 .5) . The show programmes
and sequences of scenes can be started as follows:
1) Press the button MENU repeatedly until the high-
est menu level has been reached .
2) Press the button UP or DOWN repeatedly until
the display indicates
.
3) Press the button ENTER . The display now indi-
cates the show programme most recently selected
(
…
) or the sequence of scenes most
recently selected (
…
) .
4) Use the button UP or DOWN to select the show
programme or sequence of scenes desired .
5.1.5 Programming sequences of scenes
10 sequences of scenes can be easily programmed .
A sequence may consist of up to 30 scenes which is
automatically repeated . For each scene, the colour
can be set along with its brightness, the stroboscope
function can be activated with a variable flash fre-
quency, and the duration of the scene as well as the
fading time can be defined .
1) Press the button MENU repeatedly until the high-
est menu level has been reached .
2) Press the button UP or DOWN repeatedly until
the display indicates
.
3) Press the button ENTER . The display now indi-
cates the number of the sequence most recently
changed (
…
) .
4) Use the button UP or DOWN to select the num-
ber under which the sequence of scenes is to be
stored, and then press the button ENTER . The
display indicates the number of the first scene
(
) .
5) Press the button ENTER to call up the following
setting functions:
= brightness of the colour red
= brightness of the colour green
= brightness of the colour blue
= flash frequency of the stroboscope
= duration of the scene in seconds
= fading time
Use the button UP or DOWN to set the value
desired .
6) After setting the first scene, press the button
MENU . The display indicates the number of the
scene again . Use the button UP to select the
second scene, press ENTER and then select the
settings for this scene . Repeat this procedure for
the following scenes . If not all 30 scenes are re-
quired, enter 0 as the value for the numbers of
scenes that are not to be used .
5.2 Synchronous control of multiple
spotlights (master / slave mode)
Multiple PARC-56 / RGB or PARC-64 / RGB may be con-
nected . The master unit can then control all slave
units in sync .
1) Connect the spotlights via their DMX jacks to a
chain . Please refer to chapter 5 .3 .1 “DMX con-
nection”, ignoring step 1 .
2) The units that are to be controlled by the master
unit must be defined as slave units:
a) Press the button MENU repeatedly until the
highest menu level has been reached .
