IMDES CREATIVE SOLUTIONS Schulstrasse 21 D-48455 Bad Bentheim /Gildehaus Germany T:+49(0)5924-997337 E:
© 2019
IMDES CREATIVE SOLUTIONS
15
1.15 safety instructions
Please read carefully the safety instructions, to avoid damage to humans and
DINO-CONDENS-IT
.
Prior to operate the
DINO-CONDENS-
IT
you
MUST
be read the
Owner's Manual
.
All information/operating instructions must be read carefully.
Never try to access the hot system or open the unit lid when the system is in operation.
The vapor is invisible and can cause serious burns.
Do not operate
DINO-CONDENS-
IT
without process media.
The lid of the
DINO-CONDENS-
IT
must always remain closed during operation.
Use the supplied cotton gloves to remove the soldering material.
The PCB´s and work piece carrier are still not completely cooled to temperature after the cooling has been
stopped!!
DINO-CONDENS-
IT
must be operated only as mentioned in this manual!
Installation, operation, maintenance must be carried out only by qualified and trained personnel.
Untrained persons, mentally handicapped and children must not operate the
DINO-CONDENS-
IT
!
Comply with the electrical requirements!
The workpiece carrier and the PCB´s that comes out of the
DINO-CONDENS-
IT
will still be hot.
Caution: burning risk!
(Use the cotton hand shoes delivered with the machine)
Never
use
the DINO CONDENS-IT in case of machine failures, errors and or defects these must be first
Eliminated before running the machine for production.
Immediately switch off the
DINO-CONDENS-
IT
from the line voltage in case of faulty operation and
damage and secure the main switch against uncontrolled restart!
Open the system only after complete cooling.
Disconnect the
DINO-CONDENS-
IT
from the power during maintenance work.
NEVER
by-pass, Modify, Change or manipulate the protection devices.
The
JUMBO-CONDENS-
IT
must not be modified or altered in any way without prior consultation with
IMDES CREATIVE SOLUTIONS.
Use personal protection while operating the system.
Observe all applicable national regulations and safety regulations for accident prevention and
environmental protection.
Operate the system only with completely enclosed area and not in the open.
Electrical components are NOT protected against splashing water, appropriate protection measures must
be taken by the operator.
Do not operate the unit with a lid with broken glass Window.
There is danger of cutting on broken glass of the lid. Wear suitable protective gloves when handling
broken pieces of glass.
The Safety manager has to instruct the operator on the risk of injury if he operates the machine with a
damaged or broken window.
Use only approved heat transfer mediums which are approved by IMDES CREATIVE SOLUTIONS
Process mediums, substances and materials must be investigated prior to use on their process capability.
Be aware of slipping danger by accidental leaking of reflow medium on the ground.
Cordon off the affected area and ensure that leaked medium is absorbed with a suitable bonding agent
and removed, or cleaned up.
Hot medium has a high risk for burns, the operator must, therefore, let the media cool down.
DO NOT Touch hot medium
in any case. Allow the
DINO-CONDENS-
IT
to cool down completely
before removing it from the system.
Wear sealed protective clothing and gloves during cleaning and provide adequate ventilation and exhaust.
Read and follow the safety instructions and regulations of the used cleaner and the used medium.
To drain the used medium USE suitable containers. Ensure that the used medium dumped into the drain or
into open field.
Read the safety and disposal instructions from the manufacturers of soldering pastes, PCB´s and
component.
Eating, drinking and smoking during operating near the
DINO-CONDENS-
IT
is not permitted.
Wash your hands after working with the system thoroughly with Soap and water.
If the system should be scrapped, the process fluids have to be drained and disposed of as per
regulations.
Filter materials must be disposed as hazardous waste.
