illumina MiniSeq Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 63

illumina MiniSeq Скачать руководство пользователя страница 37

Chapter 4 Maintenance

Perform a Manual Instrument Wash

Software Updates

Introduction

Maintenance procedures include manual instrument washes and system software updates when available.
No other periodic maintenance is required.

u

Instrument washes—An automatic post-run wash after each sequencing run maintains instrument
performance. However, a manual instrument wash is required under certain conditions. See

Manual Instrument Wash

.

u

Software updates—When a new version of the system software suite is available, you can update the
software automatically through a connection to BaseSpace or manually after downloading the installer
from the Illumina website. See

Software Updates

.

Preventive Maintenance

Illumina recommends that you schedule a preventive maintenance service each year. If you are not under a
service contract, contact your Territory Account Manager or Illumina Technical Support to arrange for a
billable preventive maintenance service.

Perform a Manual Instrument Wash

Manual instrument wash options include the Quick Wash and the Manual Post-Run Wash.

Wash Types

Description

Quick Wash
Duration: 20 minutes

A quick wash is required every 7 days that the instrument is idle or after an instrument
shutdown.
The wash flushes the system with a user-supplied wash solution of laboratory-grade
water and Tween 20.

Manual Post-Run Wash
Duration: 90 minutes

A manual post-run wash is required when the automatic post-run wash is not performed,
such as when a run is ended early and the flow cell is saved for later rehybridization.
The wash flushes the system with user-supplied 0.12% sodium hypochlorite and a wash
solution of laboratory-grade water and Tween 20.

NOTE

Always use a fresh dilution of NaOCl prepared within the last 24 hours. If you make a volume larger than 1 ml,
store the remaining dilution at 2°C to 8°C for use within the next 24 hours. Otherwise, discard the remaining
dilution of NaOCl.

A manual instrument wash requires the wash cartridge and a wash flow cell provided with the instrument.
Alternatively, you can use a used flow cell for the wash.

Document # 1000000002695 v02 Material # 20014309

For Research Use Only. Not for use in diagnostic procedures.

32

«
...
35
36
37
38
39
...
»

Содержание MiniSeq
































































Отзывы:

Нет отзывов