background image

Initial operation 

Operating Instructions of the dryve D3  V0.0 

10/15 

4.4 

External directional switch 

Travel movements can be remotely controlled via an external wiring. 
For this purpose, normally-open (NO) passive switching contacts are connected to X4.1 and X4.2 as well as X4.3 and X4.4. 
These switching contacts can be push buttons, relays and also optocouplers. A higher-level control system can be used via po-
tential-free contacts. The function is identical to the function of the buttons S1 and S2. 
 
If a button combination for left-hand/right-hand rotation with only 3 connecting cables is used, then X4.2 and X4.4 must be 
bridged. The common cable of the button combination must be connected to these bridged connections. 
The buttons for left and right are connected to X4.1 and X4.3 respectively 
 

 

NOTE 

No external potential must be connected to X4 as this may destroy the dryve D3. 

4.5 

 Basic settings 

In its delivery condition, all switches are set to "off" (down position). 

4.5.1 

Operating modes 

Tip mode 
 

 

 
The motor is moved to the left or right when button S1 or S2 is pressed. If the button is not pressed, the motor stops. 
 
Start to end mode 
 

 

 
The motor is moved to the left or right after pressing button S1 or S2.  
The motor stops only when: 

1. 

One of the two buttons is pressed 

2. 

The movement encounters a block whose resistance is greater than the 

Force

 which the motor is allowed. 

3. 

The 

Limit switch

 is triggered at the end of the movement. 

 

 

Содержание drylin dryve D3
















Отзывы: