background image

 

Caution 

This symbol and signal word refer to a potentially 
hazardous  situation  which  could  result  in 
personal  injury,  property  and  environmental 
damage if ignored. 

 

Caution 

This symbol and signal word refer to a potentially 
hazardous situation which could result in damage 
to the equipment if ignored. 

 

Info 

This  symbol  indicates  useful  information  and 
recommendations  as  well  as  measures  that  will 
prolong the value of your measuring and control 
system. 

 

1.2  Intended use of the device 

Use these installation and operating instructions, the identification on the rating 
plate and the technical data sheet to check whether the device is suitable for the 
intended  use/application.  The  device  complies  with  the  requirements  of  the 
European Pressure Equipment Directive 2014/68/EU. 

 

The device may only be used to indicate fill levels on containers. 

The maximum values of the pressure and temperature range of the device must be checked 
before  installation.  If  the  maximum  allowable  operating  values  of  the  device  are  lower  than 
those of the system on which it is to be installed, protective instruments for the device, such 
as pressure reducers or similar, must be provided to avoid limit situations.  The device may 
only be used in accordance with the information in these installation and operating instructions 
or for the parameters and applications agreed in the supply contract (see rating plate). The 
operator of the direct water level indicator is obliged to familiarise himself on the compatibility 
of the medium and the device. In case of doubt, contact the relevant installation manager or 
site manager. 

The correct installation position, alignment and flow direction of the device must be observed! 
Before  installing  the  IGEMA  product  on  boilers  or  containers,  it  is  essential  to  remove  all 
protective covers and, if necessary, the protective film from rating plates and sight glasses. 

 

 

 

Caution 

Содержание IGEMA SC32-SC132

















Отзывы: