background image

8

4.3.1  Display and counting method of the quantity meter

Meter reading:
•  The current meter count can be indicated 

(→ 11.2)

•  In addition the value before the last reset is saved� This value can also be 

displayed 

(→ 11.2)

The meter saves the totalled volumetric flow quantity every 10 minutes� 

After a power failure this value is available as the current meter reading� If a 

time-controlled reset is set, the elapsed time of the set reset interval is also 

saved� So the possible data loss can be maximum 10 minutes�

Counter reset:
•  There are different ways to reset the quantity meter� 

→ 10.3.4 Manual counter reset

 

→ 10.3.5 Time-controlled counter reset

 

→ 10.3.7 Counter reset using an external signal

•  If the quantity meter is not reset using one of the above-mentioned processes, 

an automatic reset will be made when the maximum volumetric flow quantity 

that can be displayed is exceeded (overflow)�

Taking into consideration the direction of flow:
•  The quantity meter takes account of the flow direction for totalisation� The fol-

lowing counting methods can be defined via the parameter [FPro] 

(→ 10.5.8)

 

[FPro]

Counting method

0+

Negative flow values (against the marked direction of flow) are not taken 

into consideration for totalling�

– +

Negative flow values are subtracted from the consumed quantity�

4.3.2  Consumed quantity monitoring via pulse output

Output 1 indicates a pulse signal when the set volumetric flow quantity has been 

reached (pulse value 

→ 10.3.3

)�

Depending on the setting of the counting method [FPro] totalling of the volumetric 

flow quantity takes into account the flow in negative direction of flow  (– +) or does 

not take it into account (0+) 

→ 4.3.1

Содержание SM4x00






































Отзывы: