IFM SM4x00 Скачать руководство пользователя страница 4

Страница: 4 / 37

1 Preliminary note

►

Instructions

Reaction, result

[…] Designation of keys, buttons or indications

→

Cross-reference

Important note

Non-compliance may result in malfunction or interference�

Information

Supplementary note�

CAUTION

Warning of personal injury�

Slight reversible injuries may result�

2 Safety instructions

• Read this document before setting up the product and keep it during the entire

service life�

• The product must be suitable for the corresponding applications and environ-

mental conditions without any restrictions�

• Only use the product for its intended purpose

(→ 3 Functions and features)

�

•

Only use the product for permissible media (→ Technical data).

• If the operating instructions or the technical data are not adhered to, personal

injury and/or damage to property may occur�

• The manufacturer assumes no liability or warranty for any consequences

caused by tampering with the product or incorrect use by the operator�

• Installation, electrical connection, set-up, operation and maintenance of the unit

must be carried out by qualified personnel authorised by the machine operator�

• Protect units and cables against damage

�

• For medium temperatures above 50 °C (122 °F) some parts of the housing can

heat up to over 65 °C (149 °F)� Moreover, during installation or in case of a fault

(e�g� housing damage) media under high pressure or hot media can leak from

the system� To avoid personal injury, take the following measures:

Содержание SM4x00






































Результаты поиска

Содержание SM4x00

Отзывы:

Похожие инструкции для SM4x00

Бренды по названию

Популярные бренды

IFM SM4x00, Руководство по эксплуатации

Результаты поиска

Содержание SM4x00

Отзывы:

Похожие инструкции для SM4x00

Бренды по названию

Популярные бренды